Milwaukee 2607-20 Manual Del Operador página 96

EXAMPLE:
00
0 Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
60
61
Functionally check the Spindle Lock
mechanism. Spindle Lock must
return briskly when released
28
from engagement in
Gear (14).
29
30
2
(4x)
31
26
FIG.
27
1
2
14
3
4
5

13
6
7
12 9
10
11
11
12
13
10 14
15
16

4
17
(4x)
18
19
1
20
(4x)
21
22
23
9
24
25
41
26
27
28
42
29
30
31
32
34
SERVICE PARTS LIST
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
CORDLESS 18 VOLT 4-1/2" CUT-OFF/GRINDER
2680-20
CATALOG NO.
78
34
37 36
35
25
1 27
28
24
1 26 27 28
32
29 30 31 32
17
9 10 11
12 13 14
PART NO. DESCRIPTION OF PART
05-78-5316 M4 x 14mm Pan Hd. Tapt. T-20 (4)
05-88-1200 M4 x 16 T-20 Screw
06-82-7236 4-20 x 5/8" Pan Hd. Plast. T-10 (1)
05-90-0225 Split Washer
14-34-0901 Handle Kit
--------------- Right Handle Halve
--------------- Left Handle Halve
--------------- Spindle Shaft
28-53-0410 Spindle Hub
34-40-0560 O-Ring
02-04-1150 Ball Bearing
34-80-2275 Internal Snap Ring
--------------- Gear
40-50-1090 Spring
22-09-1351 Electronics Module Assembly
32-05-0121 Spindle Shaft/Gear Assembly
-------------- Serviceable Brush Card
31-92-0530 Paddle Assembly
31-92-0525 Paddle Trigger
42-42-0620 Lock-Off Lever
40-50-1480 Spring
06-65-0450 Roll Pin
14-30-0852 Gearcase Kit
28-14-2452 Gearcase Assembly
--------------- Gearcase
--------------- Shaft Bushing
42-42-1100 Spindle Lock Button
40-50-1330 Spring
42-42-0580 Spindle Lock Tube
44-60-1690 Spindle Lock Pin
34-40-0450 O-Ring
--------------- Armature
STARTING
SERIAL NO.
43 3
2
(5x)
18
40
34 35 36
37 38 39
23
39
38
(3x)
20
FIG.
35
36
37
38
39
40
41
NO. REQ. 42
43
(9) 47
60
(4) 61
(1) 77

(1) 78
(1)
(1)
(1)
(1)
FIG.
(1)
(1)
(1)
11
(1)
(1)
14,37 Apply grease to all teeth of the Pinion and Gear.
(1)
(1)
26
(1)
(1)
31,32 Apply a thin coat of grease between Spindle Lock
(1)
(1)
(1)
FIG.
(1)
27
(1)
(1)
(1)
36
(1)
(1)
(1)
(1)
(1)
(1)
REVISED BULLETIN
54-38-2683
WIRING INSTRUCTION
B96E SEE PAGE 2
 = Part number change from
previous service parts list.
47
(2x)
6
15
18
77
16
47
7
22
21
19
20 21
22 23
PART NO. DESCRIPTION OF PART
--------------- Bearing Retainer
--------------- Ball Bearing
--------------- Pinion
45-36-2040 Armature Spacer
02-04-1875 Ball Bearing
18-01-3025 Service Field
43-34-0036 Disk Flange
44-40-0035 Flange Nut
12-20-2490 Service Nameplate Kit
05-88-0920 M3 x 5mm T-10 Screw w/Wash (2)
43-54-1070 4.5" T27 Guard Assembly
43-54-1090 4.5" T1 Guard Assembly
14-46-2017 Brush Card Assembly
16-01-0061 Armature Assembly
42-62-0105 Side Handle (Not Shown)
49-96-7215 Spanner Wrench (Not Shown)
LUBRICATION:
(Use Type 'Y' grease, No. 49-08-5270)
Apply a thin coat of grease to Spindle Hub O-Ring.
Place 1/8 oz. grease in Gearcase cavity.
Shaft and O-Ring.
NOTES:
Assemble Needle Bearing with vendor I.D. facing the
Gear.
Assemble Ball Bearing with seal towards Pinion and
shield towards Armature.
MILWAUKEE TOOL ● www.milwaukeetool.com
13135 W. Lisbon Road, Brookfield, WI 53005
BULLETIN NO.
54-38-2684
DATE
Mar. 2020
5
2 3 6
7 43
NO. REQ.
(1)
(1)
(1)
(3)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
Drwg. 2