Ritter BFS 52 S Instrucciones De Montaje Y De Uso página 19

English
Unfold the illustrations at the front
and back of this manual.
Please read these instructions
thoroughly before you start to use
the appliance. Keep these operat-
ing instructions in a safe place
and ensure that they are included
with the appliance if passing it on
to a third party.
Alternatively, the current operat-
ing instructions are available at
www.ritterwerk.de.
INTENDED USE
The food slicer is used for the
slicing of household foods.
The food slicer is suitable
for contact with
foodstuffs.
If the appliance is used for a
purpose other than this, or if it is
operated incorrectly, severe inju-
ries may occur or the appliance
may be damaged. All warranty
and liability claims will be ren-
dered null and void in this case.
BEFORE USING THE
APPLIANCE FOR THE
FIRST TIME
Preparation
• Before you use the appliance
for the first time, have a specialist
install it in a suitable drawer.
• Clean the appliance before
allowing it to come into contact
with any food (see CLEANING).
Setting-up the appliance
• Pull out the drawer containing
the food slicer to the stop.
A
Using both hands, lift the food
slicer out of the drawer until it
locks into place.
B
Holding the food slicer by
the slice thickness adjustment
unit (11), fold out the appliance
until it locks into place.
C
Fold up the finger protec-
tor (5a).
D
With your left hand, push
the carriage locking device (5b)
downwards and push the slice
carriage (5) into the guide groove.
12
E
Slide the left-over holder (6)
onto the finger protector.
F
Slide the slice tray (13) into
the slots provided on the side of
the appliance.
SLICING
G
Use the slice thickness
adjustment knob (11a) to set the
required thickness.
Info:
The slice thickness adjustment
scale (8) is not a millimetre
scale. For safety reasons, the "0"
position is designed to cover the
blade.
H
Place the food to be sliced
onto the slice carriage (5). Use
the left-over holder (6) to press it
gently against the stop plate (9).
Protect your hands by always
using the slice carriage and,
where applicable, the left-over
holder.
I
Exception: Excessively large
foods to be sliced.
H
Turn the appliance on using
the power switch (1). Two operat-
ing modes are available:
Temporary (Position II):
The rotary blade (2) runs as long
as the power switch is pressed
and held down in this position.
Continuous operation
(Position I): The rotary blade
runs without the power switch
being pressed and held down
until you move the switch to the
"0" position.
Info:
Never use the appliance for more
than a maximum of 5 minutes in
continuous operation.
• With the appliance running,
gently feed the food to be sliced
into the path of the rotary blade.
• Once slicing has been com-
pleted, wait until the rotary blade
has come to a complete stop.
• After each use, turn the slice
thickness adjustment knob to the
"0" position, in order to cover up
the sharp rotating blade and to
avoid any injuries.
CLEANING
Caution:
Switch the appliance off before
cleaning it; pull the power plug
out off the socket and turn the
slice thickness adjustment
knob (11a) to the "0" position.
Clean the food slicer regularly
to prevent the accumulation of
food residue. The rotary blade
must also be cleaned regularly
as described below to prevent its
surface from rusting.
Info:
Over time, an accumulation of
food residue may cause damage
to the surface of the rotary blade,
causing it to rust.
Preparation
• Remove the slice tray (13) and
the left-over holder (6).
K
With your left hand, push
the carriage locking device (5b)
downwards and pull the slice car-
riage (5) forward out of the guide
groove.
Removing the rotary blade (2):
L
Place a suitable coin on the
blade catch (3) and turn it in a
clockwise direction.
• Take hold of the rotary blade at
its rotational centre and remove it.
Cleaning after each use
• Wipe down the housing and
all removed parts, including the
rotary blade, with a damp cloth.
Occasional cleaning
• Give all removed parts, includ-
ing the rotary blade, a thorough
wash in warm soapy water (not in
the dishwasher!).
• Clean the housing behind the
blade using a dry cloth/brush.
Info:
Do not use any abrasive cleans-
ers, sponges with rough surfaces
or hard brushes to clean the
appliance.
• Dry all parts that you have
washed.