Flotec FP415515H Manual Del Usuario página 6

Replacing an Existing Convertible Pump
Shallow Well Deep Well
Replace Regulator
with:
1" Pipe Plug*
1" Tee*
Pressure
1" Nipple*
Regulator
G e
* Purchase Separately
Figure 4: Install Pressure Regulator
and Gauge for deep well. Install
Priming Tee and Gauge for
shallow well.
Discharge Suction
(Larger)
Port
Piping and Pressure
Regulator omitted
for clarity
Drive
(Smaller)
Port
Drive Pipe
sends water
down the well
to drive water
up through the
Suction Pipe
to Pump Suction
Figure 5: Drive and Suction Functions
5980 0211
Figure 6: Mount Ejector – Shallow Well
For parts or assistance, call Flotec Customer Service at 1-800-365-6832
All manuals and user guides at all-guides.com
Deep Well
Hazardous voltage . Disconnect power to pump before working
on pump or motor.
Step 1. Drain and remove the old pump. Check pipe for scale, lime, rust,
etc., and replace it if necessary.
Step 2. Install the pressure regulator and pressure gauge in the pump body
Gage
(see Figure 4).
NOTICE: Your old ejector (in the well) may not be properly matched
to your new pump. If the pump does not perform
properly, we recommend that you install ejector kit FP520-100-P2,
included with the pump.
Step 3. Install the pump and tank in the system. Make sure that all pipe
joints in the suction pipe are air-tight as well as water tight. If the
suction pipe can suck air, the pump will not be able to pull water
from the well.
Step 4. Adjust the pump mounting height so that the plumbing connections
5985 0409
do not put a strain on the pump body. Support the pipe so that the
pump body does not take the weight of piping or fittings.
Step 5. Run piping from the discharge tee in the tank flange to the household
piping. The discharge piping must be at least as large as the tank
tee. Install a relief valve in the discharge pipe capable of passing the
entire pump flow at 75 psi. Run a pipe from the relief valve to a floor
drain or some other convenient place to carry off the water.
You have just completed the well plumbing for your new pump/tank
system . Please go to Page 9 for electrical connections .
Shallow Well–(Convertible–See Page 4 for Shallow
Well Pump)
Hazardous voltage . Disconnect power to pump before working
on pump or motor.
Step 1. Drain and remove the old pump. Check the old pipe for scale, lime,
rust, etc., and replace it if necessary.
Step 2. Remove the pressure regulator from the pump body. Replace it with
a 1" NPT close nipple, a 1"x1"x3/4" NPT Tee, and a 1" NPT pipe
plug (see Figure 4). Install the pressure gage in the plugged hole in
the pump body (see Figure 4).
Step 3. Install the ejector kit. Follow the instructions provided with the kit.
Be sure to align the venturi with the top hole on the front of the
pump (see Figure 6).
NOTICE: Always replace the ejector when replacing the pump in a
shallow well installation.
Step 4. Install the pump and tank in the system. Make sure that all pipe
joints in the suction pipe are air-tight as well as water tight. If the
suction pipe can suck air, the pump will not be able to pull water
from the well.
Step 5. Adjust the pump mounting height so that the plumbing connections
do not put a strain on the pump body. Support the pipe so that the
pump body does not take the weight of piping or fittings.
Step 6. Run piping from the discharge tee in the tank flange to the household
piping. The discharge piping must be at least as large as the tank
tee. Install a relief valve in the discharge pipe capable of passing the
entire pump flow at 75 psi. Run a pipe from the relief valve to a floor
drain or some other convenient place to carry off the water.
You have just completed the well plumbing for your new pump/tank
system . Please go to Page 9 for electrical connections .
6