Publicidad
Idiomas disponibles
Idiomas disponibles
English
Installing and Removing the
Battery Pack (Fig. A)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
9
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and the other hand holding the battery pack
Fig. F
4
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Screw Driving
For driving fasteners, the reversing button should be pushed
to the left. Use reverse (button pushed to the right) for
removing fasteners. When moving from forward to reverse,
or vice versa, always release the trigger switch first.
Drilling
WARNING: Drill may stall if overloaded causing a
sudden twist. Always expect the stall. Grip the drill
firmly to control the twisting action and avoid injury.
•
Use sharp drill bits only.
•
Support and secure work properly, as instructed in the
Safety Instructions.
•
Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
•
Secure and maintain work area, as instructed in the
Safety Instructions.
8
into the tool handle, align the
8
.
8
•
Run the drill very slowly, using light pressure, until
the hole is started enough to keep the drill bit from
slipping out.
•
Apply pressure in a straight line with the bit. Use
enough pressure to keep the bit biting but not so much
as to stall the motor or deflect the bit.
•
Hold the drill firmly with two hands, one hand on the
handle, and the other gripping the bottom around the
battery area.
•
Do not click the trigger of a stalled drill off and on in an
attempt to start it. Damage to the drill can result.
•
Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
•
Keep the motor running while pulling the bit out of a
drilled hole. This will help reduce jamming.
Drilling in Wood
Holes in wood can be made with the same twist drill bits
used for metal or with spade bits. These bits should be
sharp and should be pulled out frequently when drilling to
4
clear chips from the flutes.
Drilling in Metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The
cutting lubricants that work best are sulfurized cutting oil
or lard oil.
LED Work Light
When drill is activated by pulling the variable speed
trigger switch
1
, the integrated LED work light
automatically illuminate the work area.
nOTE: The work light is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Bit Tip Storage
A bit storage slot
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
iMPORTAnT: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel, always
using identical replacement parts.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
10
is built into the base of the tool.
7
will
Publicidad
