Bosch 0601B23100 Manual Original página 36

36 | English
Assembly with SDS bolt (see figure D)
For bevel cuts when using the SDS bolt (32), before
u
sawing, first make sure that the SDS bolt cannot come
into contact with the surface of the workpiece at any
time by making a suitable adjustment to the depth
stop (42). This prevents damage to the SDS bolt and/or
the workpiece.
Removing the saw blade
– Bring the power tool into the work position.
– Swivel the retracting blade guard (16) to the back and
hold it in this position.
– Turn the SDS bolt (32) while pressing the spindle
lock (43) until it engages.
– Press and hold the spindle lock (43) and unscrew the
SDS bolt (32) by turning it clockwise (left-hand thread).
– Remove the clamping flange (48).
– Remove the saw blade (49).
– Slowly push the retracting blade guard back down.
Fitting the saw blade
When fitting the saw blade, make sure that the cutting
u
direction of the teeth (arrow direction on the saw
blade) matches the direction of the arrow on the pro-
tective guard.
If required, clean all the parts you want to fit before installing
them.
– Swivel the retracting blade guard (16) to the back and
hold it in this position.
– Place the new saw blade on the inner clamping
flange (50).
– Attach the clamping flange (48) and the SDS bolt (32).
Press the spindle lock (43) until it engages and tighten
the SDS bolt by turning it anticlockwise.
– Slowly push the retracting blade guard back down.
Operation
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Moving the fence (see figure G)
When sawing mitre and/or bevel angles, you have to pull the
left-hand or right-hand adjustable fence (2) outwards de-
pending on the cutting direction, or remove it completely.
Vertical bevel angle range
–2° to +40° Left
–2° to +35° Right
> 40° Left
> 35° Right
Horizontal bevel angle range
> 45° Left
Right
1 609 92A 8L3 | (06.03.2023)
Transport Safety Lock (see figure E)
The transport safety lock (10) makes it easier to handle the
power tool when transporting it to various working locations.
Unlocking the power tool (work position)
– Press the tool arm down slightly by the handle (13) to re-
lease the transport safety lock (10).
– Pull the transport safety lock (10) all the way out.
– Slowly guide the tool arm upwards.
Locking the power tool (transport position)
– Loosen the locking screw (6) if it is clamping the slide
device (37) in place. Pull the tool arm fully forward and
tighten the locking screw again to lock the slide device.
– Pull the depth stop (42) upwards.
– To lock the saw table (20) in place, tighten the locking
knob (23).
– Swing the tool arm downwards by the handle (13) until
you can press the transport safety lock (10) all the way
in.
The tool arm is now securely locked and ready for transport-
ation.
Preparing for operation
Extending the saw table (see figure F)
The free end of long workpieces must have something
placed underneath it or be supported.
The saw table can be extended left and right using the saw
table extensions (29).
– Loosen the clamping screw (18).
– Pull out the saw table extension (29) to the required
length.
– Retighten the clamping screw (18) to fix the saw table ex-
tension.
If necessary, reinstall the adjustable fence (2) after making
the cut.
– Loosen the locking screw (38).
– Pull the adjustable fence (2) all the way out.
– Loosen the locking screw (38).
– Pull the adjustable fence (2) all the way out.
– Lift the adjustable fence upwards and out of the way.
– Loosen the locking screw (38).
– Pull the adjustable fence (2) all the way out.
Bosch Power Tools