Roan bass next Manual De Instrucciones página 8

ADJUSTING THE FOOTREST
The pram is equipped with an adjustable footrest. To move it to the
right Position, press down the buttons on its both sides (Fig. 16).
ASSEMBLING / DISASSEMBLING
THE FRONT BAR
The seat is equipped with a safety front bar. To assemble it, slide the
plastic insets into the holes in the armrests (Fig. 17). To dismantle it,
press down the buttons located on both sides on the plastic insets and
pull it up (Fig. 18).
NOTE! Always use the seat equipped with the safety front bar.
CANOPY OF THE SEAT UNIT
Seat unit is equipped in the canopy. To assemble the canopy, slide its
attaching mechanism to the assembly opening on both sides of the seat
unit (Fig. 19). To disassemble the canopy press red buttons and take
it off the openings (Fig. 20).
RESTRAINT SYSTEM
The seat is equipped with a 5-point restraint System (Fig. 21). It should
be used from the moment a baby Starts to sit by itself. Unfasten the
belts, by releasing the forks from the central buckle, seat the baby,
adjust the length of the belts so that they fit closely to the baby's body,
without oppressing it, and then fasten the forks of all the belts to the
central buckle.
NOTE! Always use the restraint System, if the baby can sit by itself.
ADJUSTING THE BACKREST
The seat is equipped with a four-step adjustment of the backrest angle.
To lower the backrest, pull up the plastic lever in the rear part of the
backrest (Fig. 22), and then set the correct position. To lift the backrest,
it is enough to push it upwards until the correct position is achieved. It
will get locked automatically (Fig. 23).
BAG
The pram comes with a practical bag. It attaches to the pram handle
using plastic carabiners at designated points above the handle height
adjustment (Fig. 24). The bag also comes with an additional shoulder
strap and a practical baby changer.
RAIN FOIL
The pram is provided with a rain foil equipped with an air hole at the
baby's face height. To assemble it, put one end under the footrest or
under the bassinet rear, and pull the other end onto the canopy (Fig. 25).
The foil is suitable both for the deep and stroller Version.
MOSQUITO NET
The stroller is equipped with a practicable mosquito net. To assemble
the mosquito net, fasten it by fasteners to the canopy of the carrycot
(Fig. 26) and then stretch it over the carrycot and the canopy.
TO ADJUST CARRYCOT BACKREST
In order to change the carrycot backrest angle, place the metal element
in the chosen location (Fig. 27).
8
CARRYCOT CANOPY AND HANDLE
FOR CARRYING THE CARRYCOT
The carrycot comes with a canopy. Its frame also doubles up as
a handle for carrying the seat (this is a handle for carrying the carrycot
and not the entire pram).
ATTENTION! Before lifting the carrycit, position it upright (perpeendi-
cular to the ground) whilst holding it holding it by the handle. The canopy
is adjustable. To position the canopy press the round plastic buttons
near it's base (Fig. 28a, 28b).
ASSEMBLY AND DISASSEMBLY
OF THE CAR SEAT WITH ADAPTER
To assemble the car seat for group aged 0+, first assemble the adapters.
Insert each adapter properly to the right and left pocket until you hear
a clear clicking sound (Fig. 29a, 29b). Next, insert the car seat on the
adapters until you hear a clear clicking sound (Fig. 30). To disassem-
ble the car seat, press two buttons below the toy bar of the car seat
(Fig. 31) and lift the car seat up. To disassemble the adapters move
the handle located inside the adapter and lift it up (Fig. 32).
FOLDING THE FRAME:
To fold the frame, press red locking mechanism on the right side of the
handle (Fig. 33) and pull plastic handles on both sides of the stroller
(Fig. 34, 35).
BASS NEXT is equipped with additional SAS shock absorber system with
a blockade. To lock the shock absorber, press the button with green
indicator until it is red. Repeat the action on both sides of the stroller.
Both shock absorbers should always be adjusted to the same position
(on or off) to prevent uneven operation of the stroller.