Descargar Imprimir esta página

BOMANN HTD 843 CB Instrucciones De Servicio página 15

Secador de pelo

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 9
General Safety Instructions
Read the operating instructions carefully before putting the
appliance into operation and keep the instructions including the
warranty, the receipt and, if possible, the box with the internal
packing. If you give this device to other people, please also pass
on the operating instructions.
The appliance is designed exclusively for private use and for
the envisaged purpose. This appliance is not fit for commer-
cial use. Do not use it outdoors. Keep it away from sources
of heat, direct sunlight, humidity (never dip it into any liquid)
and sharp edges. Do not use the appliance with wet hands.
If the appliance is humid or wet, unplug it immediately.
When cleaning or putting it away, switch off the appliance
and always pull out the plug from the socket (pull the plug
itself, not the lead) if the appliance is not being used and
remove the attached accessories.
Do not operate the machine without supervision. If you
leave the room you should always turn the device off.
Remove the plug from the socket.
The device and the mains lead have to be checked regularly
for signs of damage. If damage is found the device must not
be used.
Do not try to repair the appliance on your own. Always
contact an authorized technician. To avoid the exposure
to danger, always have a faulty cable be replaced only by
the manufacturer, by our customer service or by a qualified
person and with a cable of the same type.
Use only original spare parts.
Pay careful attention to the following "Special Safety Instruc-
tions".
Children and Frail Individuals
In order to ensure your children's safety, please keep all
packaging (plastic bags, boxes, polystyrene etc.) out of their
reach.
WARNING!
Caution! Do not allow small children to play with the foil
as there is a danger of suffocation!
This device is not intended to be used by individuals (includ-
ing children) who have restricted physical, sensory or mental
abilities and/or insufficient knowledge and/or experience, un-
less they are supervised by an individual who is responsible
for their safety or have received instructions on how to use
the device.
Children should be supervised at all times in order to ensure
that they do not play with the device.
05-HTD 843 CB.indd 15
Symbols in these Instructions for Use
Important information for your safety is specially marked. It is
essential to comply with these instructions in order to avoid ac-
cidents and prevent damage to the machine:
WARNING:
This warns you of dangers to your health and indicates
possible injury risks.
CAUTIoN:
This refers to possible hazards to the machine or other
objects.
NoTE: This highlights tips and information.
Special safety instructions for this device
Symbols on the Product
On the products you will find symbols that indicate warnings or
provide information:
WARNING oF ElECTRIC SHoCK!
Do not use this device near baths, wash basins or
other vessels containing water.
WARNING:
The nozzles become hot during operation.
If the hair dryer is used in the bathroom, remove the mains
plug after use as water represents a hazard. This also
applies when the hair dryer is switched off.
Please ensure that the inlet grille remains free of fluff and
hairs. Danger of fire!
As additional protection we recommend the installation of a fault
current protection device (RCD) with a rated current of not more
than 30 mA in the wiring system of the bathroom. Please contact
an authorised electrician for advice.
Commissioning
Attach a nozzle if necessary.
You can dry single hair locks by concentrating the flow
of hot air with the hairdressing nozzle.
The diffuser is the ideal solution to dry curly hair without
losing volume.
In order to replace the attachment, first remove the old
attachment by pulling it off and then pushing on the new one
until it clicks into place.
Electrical Connection
Before inserting the plug into the socket. Make sure that the
mains voltage to be used matches that of the device. You
can find this information on the nameplate.
Connect the device to a duly installed 230 V/50 Hz protec-
tive contact socket.
15
11.02.2010 10:24:48 Uhr

Publicidad

loading