Gude GIH 2000 Traducción Del Manual Original página 19

Assembly
Please check the scope of delivery for completeness
before assembling this electric radiant heater. You
will find a complete list of parts at the front of the
instructions, as well as illustrations of the individual
assembly steps.
Attention! Before assembling the unit, make sure that it
is disconnected from the mains.
1. Lift the screw cover of the stand
10
the lower tube to the stand
16
the washer to the stand and then tighten
the screw . Cover it with the screw cover
17
. (Picture 1, p. 6)
2. Put the cable attachment
10 and secure it in the desired position with the
12
screw . Loosen the screws
9
tube . Screw the middle tube
tube with 4 screws
10
3. Loosen the screws 8
Screw the upper tube
8
with 4 screws (Fig. 3, p. 6).
4. Pull the extension out of the upper tube
and fix the thread 6
setting.
Insert the upper tube
of the heating head housing
3
the locking knob
2
housing to the pipe. Now plug the power
1
cable into the cable attachment
13
4, p. 7)
5. Adjust the heating head housing
desired angle between 0° and 45°. (Fig. 5, p. 7)
Electrical connection
1. Unwind the mains cable completely.
2. Make sure that the unit voltage (see type plate)
and mains voltage match.
3. Make sure that the unit is completely switched
off when you plug it in.
4. Only connect the mains plug to a properly
installed and fused socket outlet with earthing
contact.
5. Make sure that the mains cable is always routed
behind the unit - never in front of it!
6. The socket used must always be located in
an interior protected from moisture and
humidity!
Extensions of the mains cable must be selected taking
into account the appliance connection power, the
intended use and the cable length. Do not use multiple
sockets. Do not connect any other powerful appliances
to the circuit.
Make sure that extension cables are fully unwound or
14
. Connect
by attaching
15
14
11 on the lower tube
8
on the middle
9
to the lower
. (Fig. 2, p. 6)
8
on the upper tube 7 .
7 to the middle tube 9
7
to lock its desired height
7 into the tube holder
. Tighten
1
to secure the heater head
. (Fig.
11
to the
1
uncoiled.
Always check the condition of the mains cable
before using the unit. If you have any doubts about
the condition of the power cord, please contact the
customer service.
Lay the mains cable in a place where no one can trip
over it. Place the appliance so that the mains plug is
accessible at all times.
Note
Odours may occur during initial operation or after a
longer period of non-use.
Operation
Switch on the unit
If you have set up the unit correctly and ready for
operation as described in the chapter Assembly
& Commissioning, taking into account all safety
instructions, you can now switch it on.
Height adjustment
To adjust the height, you must hold the heating head
housing while loosening the thread for locking
1
Adjust the adjustable tube to the desired height. Screw
the thread tight again.
6
Warning!
As soon as the thread 6 is loosened, the heating
head housing may suddenly fall down. Therefore,
1
always hold it firmly before and while adjusting the
height. It is strongly recommended to adjust the height
before each use. Make sure that the thread to lock the
height adjustment is tightened again before using the
appliance.
Angle adjustment
The heating head housing
between 0° and 45°. To do this, simply press it into the
correct position.
Warning!
Never adjust the angle during operation.
Set heating level
With the pull switch 5 you can choose between
heating levels 1, 2 and 3. You can read the setting on
the heat level indicator
4
» O : Off
» Heating level 1: 0,65 kW
» Heating level 2: 1,35 kW
» Heating level 3: 2,0 kW
ENGLISH
6
1 allows angle adjustment
.
19
.