cecotec BONGO Z CITY Serie Manual De Instrucciones página 33

ENGLISH
NOTE:
When driving in Pedestrian mode, the flashing of the taillight and side light activates
automatically.
Power and operation
Fig. 30
1. Hold the handlebars with your hands, step on the deck with one foot, and step on the
ground with the other. Propel the scooter forward (initial speed is 5 km/h) and press the
accelerator.
2. Keep your body and the electric scooter balanced facing forward.
3. Turn the handlebar with both hands.
4. When you need to brake, hold the handlebars firmly and brake with both levers applying
the desired force. When slowing down and stopping, you should place one foot on the
ground to keep your balance.
WARNING!
- Do not ride too fast.
- The display shows the battery level. Make sure the battery is fully charged before using
the electric scooter, especially in case of long journeys.
Riding modes
1. PEDESTRIAN mode: the mode indicator on the display will show 1. In this mode, the
scooter can reach 6 km/h.
2. CONFORT mode: the mode indicator on the display will show 2. In this mode, the scooter
can reach 15 km/h.
3. SPORT mode: the mode indicator on the display will show 3. In this mode, the scooter can
reach 25 km/h.
NOTE:
Speeds were measured with an 80-kg weight, a completely charged battery, tyres with
optimum pressure, on a flat surface with no wind, and a room temperature of approximately
25ºC.
Tyre use
- For a correct operation of the electric scooter, you should check and ensure the correct
pressure on the wheels before every use.
- The optimum pressure for these tyres is de 30 PSI / 2.1 bars / 210 kPa.
- We recommend you carry out periodic tests to ensure the pressure is between the
recommended values to achieve efficient operation.
- During the shelf life of these tyres, we recommend using heat-sealing gels to prevent
punctures and maintain maximum effectiveness and performance.
64 BONGO SERIE Z CITY
BONGO SERIE Z MOUNTAIN
ORIGINAL MANUAL TRANSLATION
6. CLEANING AND MAINTENANCE
- Make sure the product is not plugged in the power supply or on before cleaning or
maintenance.
- Use a soft cloth to clean the exterior housing of the electric scooter.
- Never use alcohol, petrol, paraffin, corrosive, or abrasive products to clean the electric
scooter.
- Never immerse the electric scooter in water or any other liquid to clean it, as this could
damage the electronic parts permanently.
- Never use pressurised water to clean the electric scooter.
- Do not try to repair the electric scooter on your own. In case it does not operate correctly or
is damaged, please contact the official Cecotec Technical Support Service.
- Self-tapping nuts and other fasteners may loosen their hold and need to be retightened.
- If the scooter is expected to be inactive for more than 30 days, fully charge the battery and
place it in a cool, dry place. Remember to recharge it every 60 days to protect the battery
from possible damage beyond the scope of the warranty.
- Disassembly of the wheels is complicated and improper assembly can cause instability
and malfunction.
Brake disc
You must check the brake discs are in perfect condition, matching the brake calliper–fix this
easily with the Allen key provided. Brake pads are consumable parts and must be replaced
when their shelf life expires.
Storage
- When not in use, store the scooter in a dry and ventilated place. Do not leave it outdoors
for a long time. Excessive sunlight, overheating and overcooling accelerate tyre ageing and
compromise the service life of the scooter and its battery.
- Charge it only if the room temperature is between 0ºC and 35ºC and store it at a temperature
between -10ºC and 35ºC.
Battery release
- Battery removal is complicated and may alter the operation of the electric scooter: you
can contact an authorised repair entity if the product warranty is still valid. If the warranty
has expired, you can contact a specialist workshop of your choice. You can also contact the
Cecotec Customer Service Department.
- For proper removal of the battery for subsequent recycling, you must:
1. Remove the anti-slip rubber from the top of the scooter.
2. Loosen the screws on the upper part of the scooter.
3. Remove the metal part from the upper part.
ENGLISH
BONGO SERIE Z CITY 65
BONGO SERIE Z MOUNTAIN