Publicidad
TECHNICAL DATA
CORDLESS IMPACT WRENCH
Production code.......................................................................
No-load speed ....................................................
Impact range ......................................................
Torque ................................................................
Max. diameter bolt / nut ......................................
No-load speed ....................................................
Impact range ......................................................
Torque ................................................................
Max. diameter bolt / nut ......................................
No-load speed ....................................................
Impact range ......................................................
Torque ................................................................
Max. diameter bolt / nut ......................................
No-load speed ....................................................
Impact range ......................................................
Torque ................................................................
Max. diameter bolt / nut ......................................
Tool reception ..........................................................................
Battery voltage.........................................................................
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah...12,0 Ah) ....
Recommended ambient operating temperature ......................
Recommended battery types...................................................
Recommended charger ...........................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ........................
Sound power level (Uncertainty K=3dB(A)) .............................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
h
Impact tightening of fasteners of the maximum capacity of the tool .
Uncertainty K= ......................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT WRENCH SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a „live" wire
may make exposed metal parts of the power tool „live" and
could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing
loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
16
ENGLISH
M18 FIWP12
M18 FIWF12
M18 FIWF38
.......... 4525 29 05... .....................4525 08 05... ............... 4525 39 05...
..000001-999999
...000001-999999
...000001-999999
....... 0-1700 min
-1
.................0-1700 min
-1
..................... 0-900 min
....... 0-2400 min
-1
.................0-2400 min
-1
................... 0-1900 min
.............. 40 Nm .......................... 40 Nm .............................40 Nm
.. ≥ M12 (12.9) / ≥ M14 (8.8) ........≥ M12 (12.9) / ≥ M14 (8.8) ...≥ M12 (12.9) / ≥ M10 (8.8)
....... 0-2000 min
-1
.................0-2000 min
-1
................... 0-1600 min
....... 0-2600 min
-1
.................0-2600 min
-1
................... 0-2300 min
............ 120 Nm ........................ 120 Nm ...........................100 Nm
.. ≥ M14 (12.9) / ≥ M16 (8.8) ........≥ M14 (12.9) / ≥ M16 (8.8) ...≥ M12 (12.9) / ≥ M12 (8.8)
....... 0-2500 min
.................0-2500 min
................... 0-2500 min
-1
-1
....... 0-3100 min
.................0-3100 min
................... 0-3100 min
-1
-1
............ 300 Nm ........................ 300 Nm ...........................284 Nm
.. ≥ M16 (12.9) / ≥ M18 (8.8) ........≥ M16 (12.9) / ≥ M18 (8.8) ...≥ M16 (12.9) / ≥ M18 (8.8)
....... 0-2000 min
-1
.................0-2000 min
-1
................... 0-1600 min
....... 0-2600 min
-1
.................0-2600 min
-1
................... 0-2300 min
............ 120 Nm ........................ 120 Nm ...........................100 Nm
.. ≥ M14 (12.9) / ≥ M16 (8.8) ........≥ M14 (12.9) / ≥ M16 (8.8) ...≥ M12 (12.9) / ≥ M12 (8.8)
......1/2" (13 mm) ................1/2" (13 mm) ................... 3/8" (10 mm)
.............. 18 V ............................. 18 V ................................18 V
1,51 kg...2,63 kg .............. 1,51 kg...2,63 kg .................. 1,51 kg...2,63 kg
............................................................ -18...+50 °C
.........................................................M18B...M18HB
.............................M12-18C, M12-18AC, M12-18FC, M1418C6
........... 93,5 dB (A) .................. 93,5 dB (A) ......................93,5 dB (A)
......... 104,5 dB (A) ................ 104,5 dB (A) ....................104,5 dB (A)
............. 6,7 m/s
2
........................ 7,7 m/s
2
...........................6,7 m/s
............. 1,5 m/s
2
........................ 1,5 m/s
2
...........................1,5 m/s
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine
is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
-1
-1
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
-1
machine.
-1
Do not dispose of used battery packs in the household
refuse or by burning them. Milwaukee Distributors off er to
retrieve old batteries to protect our environment.
-1
Do not store the battery pack together with metal objects
-1
(short circuit risk).
Use only System M18 chargers for charging System M18
battery packs. Do not use battery packs from other systems.
-1
Never break open battery packs and chargers and store
-1
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as
seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and
loosen nuts and bolts wherever no mains connection is
available.
Do not use this product in any other way as stated for
normal use.
2
2
RPM SETTING
The
function is designed to give the user greater control
in application and reduce damage to the fastener or work
surface by automatically shutting the tool off after the tool
senses the mechanism impacting for approximately one
second.
M18 FIWP12, M18 FIWF12: Max RPM 2000 min
shut off after about one second of impacting
M18 FIWF38: Max RPM 1600 min
-1
about one second of impacting
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 62841-1:2015
EN 62841-2-2:2014
EN 55014-1:2017:A11 2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-11-06
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-2:2014
BS EN 55014-1:2017:A11 2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-11-06
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
OPERATION
Note: It is recommended after fastening to always check
the torque with a torque wrench.
The fastening torque is aff ected by a wide variety of factors
including the following.
• State of battery charge – When the battery is discharged
voltage will drop and the fastening torque will be reduced.
• Operation at speeds – Operating the tool at low speeds
will cause a reduction in fastening torques.
• Fastening position – Holding the tool or the driving
fastener in various angles will aff ect the torque.
• Drive accessory/socket – Failure to use the correct size
accessory or socket, or a non-impact rated accessory may
cause a reduction in the fastening torque.
• Use of accessories and extensions – Depending on the
accessory or extension fi tment can reduce the fastening
force of the impact wrench.
• Bolt/Nut – Fastening torques may diff er according to the
- tool will
-1
diameter of the nut or bolt, the class of nut/bolt and the
length of nut/bolt.
- tool will shut off after
• Condition of the fastener – Contaminated, corroded, dry or
lubricated fasteners may vary the fastening torques.
• Condition and base material – The base material of the
fastener and any component in between the surfaces may
eff ect the fastening torque (dry or lubricated base, soft or
hard base, disc, seal or washer between fastener and
base material).
IMPACTING TECHNIQUES
The longer a bolt, screw, or nut is impacted, the tighter it will
become.
To help prevent damaging the fasteners or workpieces,
avoid excessive impacting.
Be particularly careful when impacting smaller fasteners
because they require less impacting to reach optimum
torque.
Practice with various fasteners, noting the length of time
required to reach the desired torque.
Check the tightness with a hand-torque wrench.
If the fasteners are too tight, reduce the impacting time.
If they are not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the
head of the fastener aff ects the degree of tightness.
The torque required to loosen a fastener averages 75% to
80% of the tightening torque, depending on the condition of
the contacting surfaces.
ENGLISH
17
Publicidad
