Publicidad
Idiomas disponibles
Idiomas disponibles
CF15 TOOL SPECIFICATIONS
All screws and nuts are metric.
TOOL
MODEL
ACTUATION
CF15-2
Contact Trip
FASTENER SPECIFICATIONS:
This tool will accept 25mm (0.98") crown corrugated fasteners in lengths of 9mm (0.35") 12mm (.047") &
15mm (0.59").
TOOL AIR FITTING:
This tool uses a free-flow connector plug, 1/4" N.P.T. The minimum inside diameter should be .200" (5mm).
The fitting must be capable of discharging tool air pressure when disconnected from the air supply.
OPERATING PRESSURE:
70 to 120 p.s.i.g. (4.8 to 8.3 kg/cm
performance.
DO NOT EXCEED THE RECOMMENDED OPERATING PRESSURE.
AIR CONSUMPTION:
The CF15 requires 4.55 cubic feet per minute (.129m
p.s.i. (5.62 kg/cm
2
). Take the actual rate at which the tool will be run to determine the amount of air required. For
instance, if your fastener usage averages 50 nails per minute, you need 50% of the tool's c.f.m. which is required to
operate the tool at 100 nails per minute.
OPERATION
BOSTITCH OFFERS TWO TYPES OF OPERATION FOR THIS SERIES TOOL.
CONTACT TRIP:
The common operating procedure on "Contact Trip" tools is for the operator to contact the work to actuate the
trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is contacted. This
will allow rapid fastener placement on many jobs, such as sheathing, decking and pallet assembly. All
pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip, and if
unintentionally allowed to recontact the work surface with the trigger still actuated (finger still holding trigger
pulled) an unwanted second fastener will be driven.
SEQUENTIAL TRIP:
The Sequential Trip requires the operator to hold the tool against the work before pulling the trigger. This makes
accurate fastener placement easier, for instance on framing, toe nailing and crating applications.The Sequential
Trip allows exact fastener location without the possibility of driving a second fastener on recoil, as described
under "Contact Trip". The Sequential Trip Tool has a positive safety advantage because it will not accidentally
drive a fastener if the tool is contacted against the work – or anything else – while the operator is holding the
trigger pulled.
MODEL IDENTIFICATION:
Refer to Operation Instructions on page 8 before proceeding to use this tool.
CONTACT TRIP
Identified by:
BLACK TRIGGER
P
R I
T
L
A
T I
N
E
U
Q
E
S
Y :
B
D
E
F I
T I
N
E
I D
R
E
G
G
R I
T
Y
A
R
G
LENGTH
291mm (11.5")
2
). Select the operating pressure within this range for best fastener
SEQUENTIAL TRIP
Identified by:
GRAY TRIGGER
P
R I
T
T
C
A
T
N
O
C
Y :
B
D
E
F I
T I
N
E
I D
R
E
G
G
R I
T
K
C
A
L
B
HEIGHT
277mm (10.9")
3
) of free air to operate at the rate of 100 nails per minute, at 80
D
E
T
A
R
E
P
O
R
E
G
G
R I
T
Y :
B
D
E
F I
T I
N
E
I D
R
E
G
G
R I
T
K
C
A
L
B
-4-
WIDTH
WEIGHT
89mm (3.8")
2.79kg (6.19lb)
P
R I
T
L
A
T I
N
E
U
Q
E
S
P
R I
Y :
B
D
E
F I
T I
N
E
I D
R
E
G
G
R I
T
Y
A
R
G
R
E
T
T
C
A
T
N
O
C
Y :
B
D
E
F I
T I
N
E
I D
G
G
R I
T
K
C
A
L
B
Publicidad
