Publicidad
Idiomas disponibles
Idiomas disponibles
Fig. G
Dust Collection (Fig. A)
WARNING: To reduce the risk of injury, turn unit
off and disconnect it from power source before
installing and removing accessories, before
adjusting or when making repairs. Be sure the
switch is in the "OFF" position. An accidental start-up
can cause injury.
WARNING: To reduce the risk of serious personal
injury, NEVER operate this tool with perforated paper
unless the dust collection system is in place.
WARNING: Empty dust collection system frequently,
especially when sanding resin-coated surfaces such as
polyurethane, varnish, shellac, etc. Dispose of coated
dust particles according to the finish manufacturer's
guidelines, or place in a metal can with a tight fitting
metal lid. Remove coated dust particles from the
premises daily. The accumulation of fine sanding dust
particles may self ignite and cause fire.
Attach vacuum hose to the dust port
Using the Sander (Fig. G)
To operate your sander, grasp it as shown in Figure G. Hold
the tool firmly and turn it on. Apply the sanding disc to the
workpiece and apply slight pressure only. Be sure to check
your work often. This sander is capable of removing material
rapidly, especially with coarse paper.
To produce the best finish possible, start with coarse grit
sandpaper and change gradually to finer and finer paper.
Vacuum and wipe the surface with a tack cloth between
grit steps.
When sanding painted surfaces (see Additional safety
Rules for Paint Removal), you may find that the
sandpaper clogs with paint. A heat gun will work much
better to remove paint before sanding. Follow all the safety
instructions in the heat gun instruction manual.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
1
2
Accessories
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
www.dewalt.com.
Repairs
4
.
Register Online
Thank you for your purchase. Register your product now for:
•
•
•
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D
e
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and
you may have other rights which vary in certain states
or provinces.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
WARNING: Since accessories, other than those
offered by D
WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
WALT (1-800-433-9258) or visit our website:
e
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D
WALT factory service center
e
or a D
WALT authorized service center. Always use
e
identical replacement parts.
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
WALT will repair, without charge, any defects due to
English
WALT
e
WALT Industrial
e
WALT (1-800-433-9258).
e
7
Publicidad
