Milwaukee AGV 13-125 QX Instrucciones De Uso página 14

TECHNICAL DATA
Nominal power output (230 V) (W) ......................................
Nominal power output (110 V) (W) ....................................
Rated output (230 V) (W) ....................................................
Rated output (110 V) (W) .....................................................
Max. no-load speed (min ) ..................................................
-1
Grinding disk diameter (mm) ...............................................
Thread of work spindle ........................................................
Weight without cable (kg) ....................................................
Typical weighted acceleration in the
hand-arm area (m/s ) ...........................................................
2
Typical A-weighted sound levels:
Sound pressure level (dB (A)) ..........................................
Sound power level (dB (A)) ..............................................
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached leaflet!
Appliances used at many different locations including open air must
be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
After switching off, the machine will not be idle immediately. (After-
running of the work spindle.) Allow the machine to come to a stop
before putting down.
Never reach into the danger area of the plane when it is running.
Always use the auxiliary handle.
Always use the protecting cap when roughing-down and separating.
Only use tools whose permitted speed is at least as high as the
highest no-load speed of the machine.
Pay attention to the dimensions of the grinding disc. The mounting
hole diameter must fit the mounting flange without play. Do not use
reducer pieces or adapters.
Check grinding tools before use. The grinding tool must be properly
mounted and turn freely. Perform a test run for at least 30 seconds
without load. Do not use damaged, out of round or vibrating grinding
tools.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine in order
to find out the cause.
Always use and store the grinding disks according to the
manufacturer's instructions.
When grinding metal, flying sparks are produced. Take care that no
persons are endangered. Because of the danger of fire, no
combustible materials should be located in the vicinity (spark flight
zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust flying from
the workpiece come into contact with you.
Never use a cutting disc for grinding. Do not subject cutting discs to
side pressure.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work with the
machine.
The workpiece must be fixed if it is not heavy enough to be steady.
Never lead the workpiece to the grinding disk with your hand.
In case of extreme operating conditions (e.g. when smoothing
metals with the supporting disk and vulcanised fibre disks) strong
contamination can build up inside the angle grinder. In such cases it
is recommended to shorten the cleaning cycles and/or add a
residual current operated device.
SPECIFIED CONDITIONS OF USE
This angle grinder can be used for separating and grinding many
different materials, e.g. metal or stone. In case of doubt please read
the manufacturers' instruction.
Do not use this product in any other way as stated for normal use.
AG 13 AGV 13
-125 X -125 QX
....1250 ..............1250 ..............1520 ..............1520 .............. 1520 .............. 1520
....1250 ..............1250 ..............1350 ..............1350 .............. 1350 .............. 1350
.....750 ................750 ................910 ................910 ................ 910 ................ 910
.....750 ................750 ................810 ................810 ................ 810 ................ 810
...11000 ............ 11000 ....... 2600-11000 ........ 11000 ............ 11000 ........ 2000-7600
.....125 ................125 ................125 ................125 ................ 125 ................ 125
....M 14 ..............M 14 ..............M 14 ..............M 14 .............. M 14 .............. M 14
..... 2,5 ................. 2,6 ................. 2,5 ................. 2,5 ................. 2,6 ................. 2,5
..... 7,0 ................< 2,5 ............... 4,5 ................. 4,5 ................< 2,5 ............... 4,5
......89 ..................89 ..................89 ..................89 .................. 89 .................. 88
.....102 ................102 ................102 ................102 ................ 102 ................ 101
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized documents.
EN 50144, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3,
in accordance with the regulations 98/37/EC, 89/336/EEC
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to connect to
sockets without an earthing contact as the design conforms to
safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the ten-digit No. as well as the machine type printed on the label
and order the drawing at your local service agents or directly at:
Milwaukee Electric Tool, Max-Eyth-Straße 10, D-71364 Winnenden,
Germany.
ELECTRONICS
The speed of rotation is adjusted electronically when the load
increases.
In case of a longer overload period the speed is decreased
electronically. The machine continues to run slowly to cool down the
motor coil. After switching off and on the machine can be used at
rated load.
SYMBOLS
AG 16 AG 16
-125 XE -125 XC -125 QXC
Volker Siegle
Manager Product Development
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the machine.
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
ENGLISH
AGV 16 AG 16
-125 INOX
16