GRAPHITE 58G540 Manual Del Usuario página 9

Diamond drill 58G540
Parameter
Supply voltage
Supply frequency
Rated power
Protection class
No-load speed
Spindle diameter
Maximum drilling diameter
Degree of protection
Mass
Year of production
58G540 stands for both type and machine designation
NOISE AND VIBRATION DATA
Sound pressure level
Sound power level
Information on noise and vibration
The noise emission level of the equipment is described by: the
emitted sound pressure level Lp
(where K denotes measurement uncertainty). The vibrations emitted
by the equipment are described by the vibration acceleration value
a (where K is the measurement uncertainty).
h
The sound pressure emission level Lp
and the vibration acceleration value a
been measured in accordance with EN 62841-1:2015. The vibration
level a given can be used to compare equipment and to make a
h
preliminary assessment of vibration exposure.
The vibration level quoted is only representative of the basic use of
the unit. If the unit is used for other applications or with other work
tools, the vibration level may change. A higher vibration level will be
influenced by insufficient or too infrequent maintenance of the unit.
The reasons given above may result in increased vibration exposure
during the entire working period.
In order to accurately estimate vibration exposure, it is
necessary to take into account periods when the unit is
switched off or when it is switched on but not used for work.
Once all factors have been accurately estimated, the total
vibration exposure may turn out to be much lower.
In order to protect the user from the effects of vibration, additional
safety measures should be implemented, such as cyclical
maintenance of the machine and working tools, securing an
adequate hand temperature and proper work organisation.
PROBLEM SOLVING
PROBLEM CAUSE
Engine does not Device switched off or
run plug disconnected
Carbon brushes hang
up and disconnect
power supply
PRCD failed to reset
PRCD has failed
The device drills Worn drill bit
slowly
The amount of water
supplied is too low
The drill was glued
together by the spoil
Turning speed is too
high
Lace cuts steel slips
on it
Too much spoil in the
hole
Reduced water supply
or water leaks
The drill is out of
focus
The drill was The drill or the wall of
jammed the drill and the hole
has been jammed by
Value
230 V AC
50 Hz
2200 W
II
-1
0-2000 min
1 ¼"
180 mm
IPX0
11.54 kg
Lp =95.5 dB(A) K=3
A
dB(A)
Lw =106.5 dB(A) K=3
A
dB(A)
and the sound power level Lw
A
, the sound power level Lw
A
given in this manual have
h
SOLUTION
Switch on the device, insert
the plug into the power
socket
Replace carbon brushes
Press the reset button or
restart the engine
Replace the PRCD
Replace the drill bit
Increase the amount of
water supplied
Clean drill bit, increase
water pressure
Change to a lower speed
Reduce the water feed rate
once the steel has been cut,
Increase its quantity
Clean the bottom of the hole
of spoil and increase the
water pressure!
Check ball valve and water
flow
Re-sharpen the drill with a
grinder
Switch off the machine, turn
the drill to the right and left
Undercutting the
drill
Water jacket
leaks
WARNING! This equipment may be used by children 8 years of age
and older and by persons with limited physical, sensory or mental
abilities or persons without experience and knowledge, if they are
supervised or have been instructed in the safe use of the equipment
and understand the hazards that result from such use. Children must
not play with the equipment. Without supervision, children must not
clean the equipment or perform user-level maintenance.
ENVIRONMENTAL PROTECTION
A
Electrically-powered products should not be disposed of
with household waste, but should be taken to appropriate
facilities for disposal. Contact your product dealer or local
authority for information on disposal. Waste electrical
A
and electronic equipment contains environmentally inert
substances. Equipment that is not recycled poses a
potential risk to the environment and human health.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa
with its registered office in Warsaw, ul. Pograniczna 2/4 (hereinafter: "Grupa
Topex") informs that all copyrights to the content of this manual (hereinafter:
"Manual"), including, among others. Its text, photographs, diagrams, drawings,
as well as its composition, belong exclusively to Grupa Topex and are subject to
legal protection under the Act of 4 February 1994 on Copyright and Related
Rights (ie Journal of Laws 2006 No. 90 Poz. 631, as amended). Copying,
processing, publishing, modification for commercial purposes of the entire
Manual and its individual elements, without the consent of Grupa Topex
expressed in writing, is strictly prohibited and may result in civil and criminal
liability.
EC Declaration of Conformity
Manufacturer: Grupa Topex Sp. z o.o. Sp.k., Pograniczna 2/4 02-285
Warszawa
Product: Diamond drill
Model: 58G540
Trade name: GRAPHITE
Serial number: 00001 ÷ 99999
This declaration of conformity is issued under the sole responsibility of
the manufacturer.
The product described above complies with the following documents:
Machinery Directive 2006/42/EC
Electromagnetic Compatibility Directive 2014/30/EU
RoHS Directive 2011/65/EU as amended by Directive 2015/863/EU
And meets the requirements of the standards:
EN 62841-1:2015; EN 62841-3-6:2014+A11:2017;
EN IEC 55014-1:2021; EN IEC 55014-2:2021; EN IEC 61000-3-
2:2019+A1:2021; EN 61000-3-3:2013+A1:2019+A2:2021;
IEC 62321-3-1:2013; IEC 62321-4:2013+AMD1:2017; IEC 62321-
5:2013;
IEC 62321-6:2015; IEC 62321-7-1:2015; IEC 62321-7-2:2017; IEC
62321-8:2017
This declaration relates only to the machinery as placed on the market
and does not include components
added by the end user or carried out by him/her subsequently.
Name and address of the EU resident person authorised to prepare
the technical dossier:
Signed on behalf of:
Grupa Topex Sp. z o.o. Sp.k.
2/4 Pograniczna Street
02-285 Warsaw
chips. The stand is With a spanner or pull out
not properly secured, the drill bit and break up the
clumped excavated material.
Reattach the tripod, move
the tripod mounting point
The spindle is not Repair or replace the
straight spindle
The drill is not straight Replace the drill bit
Excavated material Increase the water pressure,
cannot be flushed out pull out the drill bit, clean the
of the hole hole
The gasket is worn Replace the gasket
9