Publicidad
Idiomas disponibles
Idiomas disponibles
3. Use personal protective equipment,
4. Disconnect from the power source before starting maintenance or repair
activities,
5. Use protective clothing,
6. Protect against rain,
7. Do not direct the stream at people, animals or live installations,
8. Risk of injury by high pressure,
9. Keep the children away.
CONSTRUCTION AND APPLICATION
The pressure washer is a manual type device. The drive is a DC motor.
This type of power tool is designed for washing surfaces under high
pressure of water as well as for irrigation. This battery powered device is
widely used in the household and garden. It is especially suitable for
cleaning
garden
equipment
The washer is intended solely for amateur use.
WARNING! Do not use the device contrary to its intended use.
DESCRIPTION OF GRAPHIC PAGES
The numbering below refers to the components of the device shown on
the graphic pages of this manual.
1. Trigger lock button
2. The trigger
3. Pressure button (Eco)
4. Handle
5. The nozzle
6. Ventilation slots
7. Long lance
8. Nozzle
9. Lock ring
10. Short lance
11. Adapter with valve
12. Detergent spray nozzle
13. Detergent container
14. Snake
15. Hose quick coupler
16. Filter
17. Swimmer
18. Clip with a handle
* There may be differences between the drawing and the product.
EQUIPMENT AND ACCESSORIES
1. Long lance
2. Nozzle
3. Short lance
4. Adapter with valve
5. Drawn detergent nozzle
6. Detergent container
7. Snake
8. Hose quick coupler
9. Filter
10. Swimmer
11. Clip with a handle
PREPARATION TO WORK
ASSEMBLY / REMOVAL OF THE SHORT LANCE WITH NOZZLE
Pull the locking ring (9) back, insert the tip of the nozzle (8) into the
hole of the short lance (10)
(fig. A).
Release pressure on locking ring (9), check correct connection.
The removal of the nozzle takes place in the reverse order of its
assembly.
WARNING! Check that the spray nozzle is properly secured.
INSTALLATION / REMOVAL AND HANDLE PISTOL LANCE
Connect the short lance (10) with the pistol grip (4) of the device by
gently pressing (paying attention to the notches in the connection)
and turning it 90
°
clockwise
(fig. B).
The long lance (7) is installed in the same way (Fig. C)
The lance is disassembled in the reverse order to its assembly.
ASSEMBLY / DISASSEMBLY OF THE SHORT AND LONG LANCE
Connect the two lances by gently pressing (paying attention to the
notch in the joint) and turning by 90
D).
Lances are disassembled in the reverse order to their assembly.
OPERATION / SETTINGS
CHOOSE YOUR WATER SOURCE
and
watering
plants.
°
in relation to each other. (fig.
Connecting water from the tank
Attach the quick-connect hose (15) to the socket (5) of the appliance (fig.
E).
Place the hose (14) with the filter (16) in the water tank, position the float
(17) so that it remains on the water surface and secure with the clip with
the handle (18). The clip with a handle (18) should be clamped on the hose
(14) and hung on the wall of the tank.
WARNING! After connecting the hose, check the connection by
gently pulling on the hose.
WARNING! Do not use the device with a water source that is cloudy,
muddy, or corrosive. Suitable water sources: Bucket / waterbag /
ditches / canals / lakes / sea (The system must be flushed completely
with fresh water after use) (fig. F).
WARNING! When using open water (ditches / canals / lakes etc),
make sure the filter stays far from the bottom (move the float if
necessary). Always use the supplied filter hose.
WARNING! Before use, remove the air from the hose, hold (max. 1.5
m above the water source) and turn on the device. It may take about
30 seconds for water to reach the machine.
Water connection from the mains
Disconnect the hose (14) from the machine using the quick-connect
hose (15).
Connect the adapter with valve (11) to the connection piece (5) of the
device (fig. G).
Connect the garden hose to the nipple of the valve adapter (11) (use a
standard water hose with a suitable quick coupler).
WARNING! Always use the supplied adapter with valve for mains
water (drinking) water supplies. It is recommended to close the
adapter valve when the device is not in use (an open valve causes
water to flow out of the nozzle at the specified pressure).
WARNING! The water that has flowed through the adapter is
considered unfit for drinking.
ON / OFF
WARNING! Before starting work, make sure the battery is fully
charged.
Turn on - Press the trigger lock button (1) and pull the trigger (2)
(Fig. H).
Turn off - Release pressure on trigger (2).
PRESSURE SETTING
The device has two pressure settings. The high pressure setting is suitable
for thorough removal or cleaning, and the low pressure setting is suitable
for light cleaning and watering. The device is normally set to high pressure
mode. Press the pressure button (Eco) (3) to activate the low pressure
mode (fig. I).
SPRAY MODE SELECTION
Spray options are selected by turning the front nozzle ring (8).
Select the spray mode according to the type of work. The 0 ', 15', 25 ', 40' and
Jet spray settings are suitable for cleaning and the positions with the spray
symbol are best for watering (fig. J).
WARNING! Do not change the spray setting after turning on the machine.
DETERGENT SPRAY ASSEMBLY
WARNING! Always use the detergent spray nozzle (12) in
combination with the long lance (7) only.
Attach the long lance (7) to the device (fig. C).
Attach the detergent spray nozzle (12) to the long lance (7) connected
to the machine (fig. K).
Unscrew the detergent container (13) from the detergent spray nozzle
(12) and fill with the appropriate cleaning agent.
Reattach the detergent container (13) to the detergent spray nozzle (12).
Aim the detergent spray nozzle (12) at the surface to be coated with
detergent and release the trigger lock button (1).
Press the trigger (2) and then the pressure button (Eco) (3) if necessary
to activate the low pressure mode (the detergent placed in the tank will be
sucked in and mixed with the water).
After finishing work, empty the detergent container.
WARNING! When using the water (drinking) network, make sure that
the water supply is blocked (for example by the adapter valve (11))
7
Publicidad
