Publicidad
Idiomas disponibles
Idiomas disponibles
English
Fig. AA
Worklight Cleaning
For the best worklight performance, perform the following maintenance regularly.
1. Carefully clean sawdust and debris from worklight lens with a cotton swab.
2. DO NOT use solvents of any kind, they may damage the lens.
3. Dust build-up can block the worklight and prevent it from accurately indicating the line
of cut.
4. Follow miter saw's instruction manual to remove and install blade.
5. With blade removed from saw, clean pitch and build-up from blade. Pitch and debris can
interfere with the worklight and prevent it from accurately indicating the line of cut.
SPECIFICATIONS
Light source
Worklight
Power Supply
Operating Temperature
Storage Temperature
Environmental
Dust Duct Cleaning
Depending on your cutting environment, saw dust can clog the dust duct and may prevent dust
from flowing away from the cutting area properly. With the saw unplugged and the saw head
raised fully, low pressure air or a large diameter dowel rod can be used to clear the dust out of the
dust duct.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D
WALT recommended accessories should be used with this product.
e
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center. If you need assistance in locating any accessory, please contact
D
WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-D
e
(1-800-433-9258) or visit our website: www.dewalt.com.
Optional Accessories
The following accessories, designed for your saw, may be helpful. Use care in selecting and
using accessories.
Extension Work support: DW7080
Used to support long overhanging workpieces, the work support is user assembled. Your saw
base is designed to accept two work supports, one on each side.
Adjustable length stop: DW7051
Requires the use of one Extension Work Support (DW7080). It is used to make repetitive cuts of
the same length from 0 to 42" (107 cm).
Clamp: DW7082
Used for firmly clamping workpiece to the saw fence for precision cutting.
12
59
53
Power LED
3.3 V DC
Input: 120–240 V AC; 50/60Hz
Output: 5 V DC; 0.45 A
14°F to 104°F (-10°C to 40°C)
-22°F to 176°F (-30°C to 80°C)
Water resistant
WALT, have not been tested
e
WALT
e
Dust Bag: DW7053
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the
sawdust produced.
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
saw Blades
ALWAYS USE 12" (305 mm) SAW BLADES WITH 1" (25.4 mm) ARBOR HOLES. SPEED RATING
MUST BE AT LEAST 4800 RPM. Never use a smaller diameter blade. It will not be guarded
properly. Use crosscut blades only! Do not use blades designed for ripping, combination blades
or blades with hook angles in excess of 7˚.
BLADE DESCRIPTIONS
APPLICATION
DIAMETER
Construction Saw Blades (maximum thin kerf with anti-stick rim)
General Purpose
12" (305 mm)
Fine Crosscuts
12" (305 mm)
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
12" (305 mm)
Non-ferrous metals
12" (305 mm)
NOTE: For cutting non-ferrous metals, use only saw blades with TCG teeth designed for this purpose.
Repairs
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement, when applicable) should be
performed by a D
WALT factory service center or a D
e
use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRAnTY sERViCE: Registering your product will help you obtain more efficient warranty
•
service in case there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of an insurance loss, such as fire, flood or theft,
•
your registration of ownership will serve as your proof of purchase.
FOR YOUR sAFETY: Registering your product will allow us to contact you in the unlikely
•
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D
WALT will repair, without charge, any defects due to faulty materials or workmanship for
e
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
WALT (1-800-433-9258). This warranty does not apply
e
to accessories or damage caused where repairs have been made or attempted by others. THIS
LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so these
limitations may not apply to you. This warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
WALT tools are covered by our:
e
1 YEAR FREE sERViCE
D
WALT will maintain the tool and replace worn parts caused by normal use, for free, any time
e
during the first year after purchase.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of your D
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for
a full refund – no questions asked.
lATin AMERiCA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning labels become illegible or are missing,
call 1-800-4-D
WALT (1-800-433-9258) for a free replacement.
e
TEETH
32/40
60
80
96
WALT authorized service center. Always
e
WALT Power Tool, Laser, or
e
Publicidad
