Publicidad
Idiomas disponibles
Idiomas disponibles
The position you select for the refrigerator installation should be well-ventilated and has less hot air. Do not locate the
refrigerator near a heat source such as cooker, boiler, and avoid it from direct sunlight, thus guaranteeing the
refrigeration effect while saving energy consumption. Do not locate the refrigerator in the damp place, so as to prevent
the refrigerator from rusting and leaking electricity.
being divided by the total space of the room in which the refrigerator is installed shall be less than 8g / m³.
Note: The amount of refrigerant charged for the refrigerator can be found on the nameplate.
2. Heat dissipation space
When working, the refrigerator gives off heat to surroundings. Therefore, at least
at the top side, more than 100mm on both sides, and above 50mm at the back side of the refrigerator.。
Dimensions in mm
W
D
540
551
540
551
Note：Figure 1, Figure 2 only as a product space demand size schematic diagram.
3.Level ground
Place the refrigerator on the solid and flat ground (floor) to keep it stable, or else, it will give rise to vibration and noise.
When the refrigerator is placed on such flooring materials as carpet, straw mat, polyvinyl chloride, the solid backing plates
should be applied underneath the refrigerator, so as to prevent color change due to heat dissipation.
Unobstructed ventilation shall be maintained around the appliance or in an embedded structure.
Preparations for use
1.
Standing time
After the refrigerator is properly installed and well cleaned, do not switch it on immediately. Make sure to energize the
refrigerator after more than 1 hour of standing, so as to ensure its normal operation.
2.
Cleaning
Confirm the accessory parts inside the refrigerator and wipe the inside with a soft cloth.
3.
Power-on
Insert the plug into the solid socket to start the compressor. After 1 hour, open the freezer door, if the temperature inside
the freezer compartment drops obviously, it indicates the refrigeration system is working normally.
4.
Storage of food
After the refrigerator runs for a period of time, the internal temperature of the refrigerator will be automatically controlled
according to the user's temperature setting. After the refrigerator is fully cooled, put in foods, which usually need 2~3
hours to be fully cooled. In summer, when the temperature is high, it takes more than 4 hours for the foods to be fully
cooled (Try to open the refrigerator door as less as possible before the internal temperature cools down).
If the refrigerator is installed in the moisture place, make sure to check whether the ground wire and leakage circuit
breaker are normal. If vibration noises are produced due to the refrigerator contacting the wall or if the wall gets blackened
by air convection around the compressor, move the refrigerator away from the wall. Setting up the refrigerator may cause
jamming noise or image chaos to the mobile phone, fixed-line telephone, radio receiver, television set surrounding it, so
try to keep the refrigerator as far away as possible in such case.
IV.
Functions
Temperature seting
The temperature of the appliance can be adjusted by turning the thermostat dial.
The thermostat can be set between 1 and 7.
• 1 is the warmest setting.
• 7 is the coldest setting.
• Set the dial to OFF to turn off the cooling function.
Under the normal operating condition (in spring and autumn), it is recommended to set the
temperature at 4 .
In summer when the ambient temperature is high, it is recommended to set temperature at 3-4 , so as to guarantee
the fridge and freezer temperatures and reduce the refrigerator continuous running time; and in winter when the
ambient temperature is low, it is recommended to set temperature at 5-6 to avoid frequent start/stop of the
H
A
B
1428
910
1054
1690
910
1054
The result of the refrigerant charge amount of the refrigerator
E
C(°)
130±5
50
130±5
50
7
30mm
of free space should be spared
F
MODEL
100
BCD-211
100
BCD-261
Publicidad
