Stokke TRIPP TRAPP Instrucciones De Uso página 10

IMPORTANT!
UK/IE
READ CAREFULLY AND
KEEP FOR FUTURE
REFERENCE
Never leave the child unattended at any times.
The Tripp Trapp® Baby Set is a passive restraint system that comply
with the standard EN 14988:2017+A1:2020. It protects your baby
from falling off the chair and restricts climbing out. Although limit-
ing the child's mobility, Stokke offers an additional, active restraint:
a harness that may further reduce the risk of falling.
The Tripp Trapp® Baby Set is only intended to be used for a short
period of time. When the child has acquired the skill of climbing
in and out of the Tripp Trapp® chair as well as the skill of dynamic
sitting, the Baby Set should be removed.
WARNING!
•
This product is intended for children able to sit up unaided and
up to 3 years or a maximum weight of 15 kg.
•
Do not use the high chair until the child can sit up unaided.
•
Make sure the Tripp Trapp® Baby Set™ is properly fastened
before you seat your child in the Tripp Trapp®.
•
Do not use the Tripp Trapp® Baby Set™ if any part is broken, torn
or missing.
•
Do not use the product unless all components are correctly
tted and adjusted.
•
Never leave the child unattended.
•
Falling hazard: Prevent your child from climbing on the product.
•
Be aware of the risk of tilting when your child can push its feet
against a table or any other structure.
10 | TRIPP TRAPP ® BABY SET
•
Be aware of the risk of open res and other sources of strong
heat in the vicinity of the product.
•
Do not place the high chair near an open re or other sources
of strong heat, such as electric bar res, gas res etc due to the
risk of re.
Assembly instructions
1 The seat plate must be in the top slot, and adjusted like shown
in picture.
2 Place the Baby Set high back onto the chair's back rest.
3 Ensure that all 4 hooks are fastened. The Baby Set high back
must be centered on the chair's back rest, or else you will not be
able to mont the Baby Set rail.
4 Slide the hooks of the Baby Set rail between the chair's back rest
bars. (You might need to push the rail a bit together, to make it
fit between the siderunners).
5 Make sure the Baby Set Rail is securely hooked to the chair's
upper back rest bar.
6 Rotate the rail down to snap the crotch strap buckle to the seat
plate. You will hear a "click" when it is locked.
Extended Glider assembly
To further increase the backward stability of the Tripp Trapp® high-
chair, an extended glider has been developed for the Tripp Trapp®
highchair. We recommend that you always use the Tripp Trapp®
Extended Glider while the chair is being used with a harness or the
Tripp Trapp® Baby Set™.
Please also see the warning section of the User Guide:
"To make sure that the gliders function as intended, the chair should be
placed on a surface that doesn't inhibit it from sliding backwards. That
means that the surface should be level, stable and with a certain hard-
ness. Carpets and rugs being soft or with long, loose ends which the
highchair could sink into, is an unsuitable surface for your Tripp Trapp®
highchair. Rough surfaces [Uneven floors], e.g. some tiled floors, are
also unsuitable for highchairs, such as Tripp Trapp®."
•
NEVER use the Tripp Trapp® highchair without any glider.
•
NEVER let your child play around the Tripp Trapp® highchair if it
is not in the intended position for use
-
. –
.
Tripp Trapp® Baby Set
.EN14988:2017+A1:2020
.
Stokke
.
Tripp Trapp® Baby Set
. 15
Trapp® Tripp
.
Trapp® Tripp
.
.
.
.
.
.
.
®Tripp Trapp
.Baby Set
!
•
3
•
•
•
•
: •
•
•
USER GUIDE