Bosch GST 10.V-LI Manual Original página 16

16 | English
(21) Shock protection guard
A)
(22) Extraction hose
(23) Base plate screw
(24) Hex key
(25) Scale for mitre/bevel angles
(26) Locking screw for parallel guide
(27) Parallel guide with circle cutter
A)
(28) Circle cutter centring tip
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless jigsaw
Article number
Rated voltage
No-load stroke rate n
0
Stroke
Max. cutting depth
– In wood
– In aluminium
– In steel (unalloyed)
Max. cutting angle (left/
right)
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
B)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-11.
Typically, the A-weighted sound pressure level of the power
tool is 75 dB(A). Uncertainty K = 5 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-11:
Cutting boards with saw blade T 111 C:
2 2
a = 4.5 m/s , K = 1.5 m/s ,
h,B
Cutting sheet metal with saw blade T 118 A:
2 2
a = 4.5 m/s , K = 1.5 m/s .
h,M
1 609 92A 4TB | (28.03.2019)
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
A)
power tool is used for other applications, with different ap-
A)
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
GST 12V-70
over the total working period.
3 601 EA1 0..
Implement additional safety measures to protect the oper-
V= 12
ator from the effects of vibration, such as servicing the
−1 power tool and application tools, keeping their hands warm,
min 1500–2800
and organising workflows correctly.
mm 18
Assembly
mm 70
u
mm 3
mm 3
° 45
A)
kg 1.5–1.7
Battery Charging (see figure A)
u
°C 0 to +45
°C –20 to +50
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
GBA 12V...
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
GAL 12...
reducing its service life. Interrupting the charging process
GAX 18...
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
To remove the battery (1), press the release button (2) and
pull the battery downwards out of the power tool. Do not
use force to do this.
Battery charge indicator
The three green LEDs of the battery charge indicator (4) in-
dicate the state of charge of the battery (1). The battery
charge indicator only lights up for five seconds after start-
up.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Bosch Power Tools