Publicidad
Idiomas disponibles
Idiomas disponibles
· TRANSLATION OF THE ORIGINAL · ENGLISH
EN
•
ON / OFF SWITCH easily accessible.
•
KEY TO PREVENT UNAUTHORISED USE remove the
yellow key from the switch and place it in a location
that is not accessible to children and other people
who are not qualified to use the tool.
•
FENCE for carrying out repetitive cuts and using the
guide for angle cuts.
•
SPLASH GUARD to contain excessive spray.
•
WRENCH STORAGE to prevent them from being lost.
4.3 Package contents
Package content (Page 34)
1. Tile cutter
Includes:
2. Shaft nut wrench
3. Arbor wrench
4. Inner blade washer
5. outer blade washer
6. Arbor nut
7. Tilting table
8. 7" diamond blade
9. Fence
10. Angle guide
11. Splash guard with konb and hexagonal bolt.
12. Support for splash guard
13. Rear table extension
14. Drain plug
15. User's manual
5.- ASSEMBLY INSTRUCTIONS
After unpacking the machine, carefully check for
damaged or broken parts. If you find any damaged or
malfunctioning parts, replace them with original spare
parts from RUBI and contact RUBI's after-sales service.
This product requires assembly.
•
Prepare a stable surface and clear it of any other
materials for use as a surface for supporting the
machine.
•
Do not throw away the packaging material until you
have carefully inspected and satisfactorily used the
tool.
ATTENTION: Most of the loose parts are stored in the
water tank.
WARNING:
If a part is damaged or missing, do not use the tool until
the parts are replaced.
WARNING:
Do not connect the machine to the power source until it
is fully assembled.
HOLES FOR MOUNTING
This tile saw has four bolt holes in the base of the saw
and can be mounted on a firm support surface, such as
a workbench, if needed. Each of the four mounting holes
must be securely bolted with 3/8" machine bolts, washers
and hex locknuts (not included).
5.1 Installation of the diamond blade
- 6 -
Español
English
Installation of the diamond blade (Figure 2, 3)
•
Disconnect the machine and remove the tilting table.
•
Fit the blade's inner washer on the arbor.
•
Place the diamond blade on the arbor and over the
sleeve on the inner washer, and push it flat against the
inner washer.
ATTENTION: Ensure that the arrows on the diamond blade
point in the counter-clockwise direction.
•
Fit the blade's outer washer on the arbor against the
diamond blade.
•
Install the arbor nut on the arbor. Using the hexagonal
wrench for the nut and the arbor wrench, firmly
tighten the arbor nut.
ATTENTION: A 7-inch blade is the maximum capacity of
the saw. Never use a disc neither larger nor thicker
5.2 I nstallation of the splash guard
Installation of the splash guard. (Figure 4, 5, 6)
•
Remove the tilting table.
•
Loosen and remove the screws located on the housing
under the table.
•
Slide the support for splash guard onto the housing.
•
Replace the screws.
ATTENTION: Ensure that the guard support is aligned with
the cutting blade so that it does not interfere with the
material that is being cut.
•
If splash guard is removed align the splash guard with
the blade and slide it over its support. Align it through
the holes in the guard with the slot on the splash
guard support.
ATTENTION: Always set the splash guard horizontally to
the table and slightly above the thickness of the tile.
•
Install the hex screw through the guard and support.
Screw the splash guard locking knob onto the bolt and
tighten to the desired height.
•
Reinstall the tilting table.
5.3 Installation or the rear table extension
Installing the rear table extension (Figure 7)
•
Align the wing screws with the holes on the back of
the saw, beneath the saw table.
•
Turn each wing screw until the rear table extension is
securely fastened.
5.4 Installation of the fence
Installation of the fence. (Figure 8, 9)
•
Raise the locking lever and place the front of the fence
(1) on the front edge of the cutting table.
•
Lower the back of the fence (2) towards the table.
•
Adjust the fence to the desired position using the
Publicidad
