Publicidad
Idiomas disponibles
Idiomas disponibles
may have become misaligned during transportation.
Furthermore, after a period of time, it will probably be
necessary to readjust due to wear.
For more precise results, the fence must be aligned with
the disc blade.
•
Make sure that the blade has been correctly
installed on to the arbor and that the arbor nut is
properly tightened.
•
Raise the splash guard.
•
Slightly loosen the two screws at the top of the
fence.
•
Carefully adjust the fence until it touches both front
and rear edges of the blade. Do not press against
the blade. Adjust the fence until there are no gaps
between the blade and the edge of the fence.
•
Lock the clamp.
•
Tighten the two screws at the top of the fence.
•
Set the scale on the fence to "0" next to the blade.
7.3 Adjusting the splash guard holder
Adjusting the splash guard holder (Figura 22)
•
Unplug the saw and remove the tilting table.
•
Raise the splash guard.
•
Loosen the three support screws.
•
With the fence touching the disc blade, adjust
the splash guard holder until it is aligned with the
fence.
•
With a Phillips screwdriver, tighten the screws.
7.4 Adjust the locking lever
Adjust the locking lever (Figure 23)
Over time, the fence may loosen. If the fence does not lock
securely to the saw table, it may require adjusting.
•
With a hexagonal wrench, loosen the cam screw.
•
Turn the cam to tighten as desired.
NOTE: An arrow is visible on the rotor. The wider end of
the arrow is the tighter end of the setting. The smaller end
of the arrow is the looser end of the setting.
•
After making the desired adjustment, firmly tighten
the cam screw.
7.5 Adjusting the sliding of the fence
Adjusting the sliding of the fence (Figure 24)
If the fence does not move smoothly along the table, it can
be loosened or tightened using the fixing screws on each
side of the cutting guide.
•
With a hexagonal wrench, loosen or tighten the
fixing screws to adjust the fence movement as
desired.
•
Attach the fence to the table and ensure that it
slides with ease. Make additional adjustments for
fence alignment if necessary.
· TRANSLATION OF THE ORIGINAL · ENGLISH
English
English
7.6 After-sales service
Use only original spare parts supplied by the manufacturer.
Repairs should only be done by certified workshops or
RUBI's technical service:
RUBI TOOLS USA Inc.
3980 West 104th Street,
Suite 6
Hialeah, FLorida (33018)
+1 305-715-9892
+1 305-715-9898
+34 682 16 90 55
rubitools.usa@rubi.com
8.- GUARANTEE
The guarantee covers all manufacturing or assembly
defects in accordance with the legislation in force. The
guarantee does not cover malfunctions cause by improper
use, overloads, failure to follow the operating instructions
and normal wear and tear. Handling by personnel other
than our Official Service shall void the guarantee. The
proof of purchase must be included with this document
for any claims.
For more details and information, consult the general
guarantee conditions at: www.rubi.com
9.- CETIFICATE
CONFORMS TO
UL STD 987
CERTIFIED TO
CSA STD C22.2 NO. 71.2:2010
5012917
STORAGE
Store the tool in its packaging in a cool, dry place protected against cold
and direct sunlight.
WASTE MANAGEMENT
The machine must be put out of service and dismantled in accordance
with the instructions in each country, at a selective collection point for
the proper classification and processing of the materials.
The reproduction of the work, in whole or in part, in any format or by any means
or procedure, whether mechanical, photographic or electronic, without the prior
authorisation of GERMANS BOADA, S.A. is prohibited.
Any of these activities shall incur the corresponding legal
in criminal prosecution.
GERMANS BOADA, S.A. reserves the right to make any technical modification
without prior notice.
EN
liabilities and could result
- 9 -
Publicidad
