Publicidad
Idiomas disponibles
Idiomas disponibles
READ ALL INSTRUCTIONS BEFORE OPERATING AND RETAIN
INSTRUCTIONS FOR FUTURE REFERENCE
TONE MODE
1. Turn Digital Toner-Pro on by pressing the Power On/Off button
2. The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
, and Wire Map Indicator
blinking, depending on whether the Toner is connected to a network port.
blinking, depending on whether the Toner is connected to a network port.
blinking, depending on whether the Toner is connected to a network port.
3. Set the tone mode to either digital toning or analog toning by pressing
Set the tone mode to either digital toning or analog toning by pressing
the Digital/Analog Tone Button
the Digital/Analog Tone Button
Digital Tone Indicator
Digital Tone Indicator
Digital Tone Indicator
One or both Analog Tone Frequency Indicators
One or both Analog Tone Frequency Indicators
One or both Analog Tone Frequency Indicators
One or both Analog Tone Frequency Indicators
One or both Analog Tone Frequency Indicators
analog toning mode. There are three frequencies available to choose from
analog toning mode. There are three frequencies available to choose from
analog toning mode. There are three frequencies available to choose from
when in analog mode: 1000Hz, 1500Hz, and 1000/1500Hz warble.
NOTE: When performing analog toning via the RJ45 port, the tone can be sent
down an individual pin, a pin pair, or to all eight pins simultaneously. To cycle
down an individual pin, a pin pair, or to all eight pins simultaneously. To cycle
down an individual pin, a pin pair, or to all eight pins simultaneously. To cycle
down an individual pin, a pin pair, or to all eight pins simultaneously. To cycle
thru the analog tone options, repeatedly press the Pin/Pair Selector Button
thru the analog tone options, repeatedly press the Pin/Pair Selector Button
thru the analog tone options, repeatedly press the Pin/Pair Selector Button
to select the desired mode. The Wire Map Indicator
or pin pairs will be toned. When performing digital toning via the RJ45 port, the
or pin pairs will be toned. When performing digital toning via the RJ45 port, the
or pin pairs will be toned. When performing digital toning via the RJ45 port, the
signal is only sent to pin pair 3-6. Wire Map Indicator LEDs 3 and 6 will blink if
toner is connected to an active network port, otherwise LEDs 3 and 6 will remain
constantly illuminated.
TRACING PAIRED WIRES (FIG. 1)
1. Connect the Digital Toner-Pro's red
Connect the Digital Toner-Pro's red
respective Test Lead Inputs
2. Connect the red ABN Test Clip
Connect the red ABN Test Clip
Connect the red ABN Test Clip
Connect the black ABN Test Clip
Connect the black ABN Test Clip
Connect the black ABN Test Clip
3. Turn Digital Toner-Pro on by pressing the Power On/Off button
4. The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
, and Wire Map Indicator
T13 T13 T13
may be blinking, depending on whether the Toner is connected to
may be blinking, depending on whether the Toner is connected to
may be blinking, depending on whether the Toner is connected to
may be blinking, depending on whether the Toner is connected to
may be blinking, depending on whether the Toner is connected to
may be blinking, depending on whether the Toner is connected to
may be blinking, depending on whether the Toner is connected to
a network port. When performing analog toning, check the "CONT"
a network port. When performing analog toning, check the "CONT"
a network port. When performing analog toning, check the "CONT"
Indicator
T4
NOTE: When performing Digital Toning, the "CONT" Indicator
When performing Digital Toning, the "CONT" Indicator
When performing Digital Toning, the "CONT" Indicator
When performing Digital Toning, the "CONT" Indicator
not illuminate.
5. Select the preferred tone setting using the Digital/Analog Tone Button
6. Turn on the Digital Probe-Pro (sold seperately).
7. At the far end of the cable, spread the wires apart at least 2" (51 mm), if possible.
8. If performing analog toning, ensure the Digital Toner-Pro and the Digital Probe-
If performing analog toning, ensure the Digital Toner-Pro and the Digital Probe-
If performing analog toning, ensure the Digital Toner-Pro and the Digital Probe-
Pro are set to ANALOG MODE.
Pro are set to ANALOG MODE.
9. If performing digital toning, ensure the Digital Toner-Pro and the Digital Probe-
If performing digital toning, ensure the Digital Toner-Pro and the Digital Probe-
If performing digital toning, ensure the Digital Toner-Pro and the Digital Probe-
Pro are set to DIGITAL MODE.
Pro are set to DIGITAL MODE.
10. Use the Digital Probe-Pro (sold seperately) to scan the cable's wire pairs.
Use the Digital Probe-Pro (sold seperately) to scan the cable's wire pairs.
Use the Digital Probe-Pro (sold seperately) to scan the cable's wire pairs.
Move the Digital Probe-Pro's tip slowly across the wires. The probe's volume
Move the Digital Probe-Pro's tip slowly across the wires. The probe's volume
will increase as it approaches the toned pair. When the probe's volume is high
over the first wire, low in the middle (between) the two wires, and high over
over the first wire, low in the middle (between) the two wires, and high over
over the first wire, low in the middle (between) the two wires, and high over
the second wire, you have located the pair of wires you are tracing. Use the
the second wire, you have located the pair of wires you are tracing. Use the
Volume Increase and Volume Decrease buttons to adjust the volume.
OPERATING INSTRUCTIONS
LEDs 3 and 6 illuminated. The LEDs may be
LEDs 3 and 6 illuminated. The LEDs may be
LEDs 3 and 6 illuminated. The LEDs may be
LEDs 3 and 6 illuminated. The LEDs may be
T18 T18 T18
, will illuminate when in digital toning mode.
, will illuminate when in digital toning mode.
, will illuminate when in digital toning mode.
, will illuminate when in digital toning mode.
, will illuminate when in digital toning mode.
, will illuminate when in digital toning mode.
T13 T13
T20 T20 T20
T14 T14
. If illuminated green, you may proceed.
. If illuminated green, you may proceed.
. If illuminated green, you may proceed.
to cycle thru the different options. The
T7 T7
and black
T14 T14
T15 T15
to one of the wires of the pair to be traced.
to one of the wires of the pair to be traced.
to the other wire to be traced.
to the other wire to be traced.
T15 T15
LEDs 3 and 6 illuminated. The LEDs
LEDs 3 and 6 illuminated. The LEDs
T18 T18 T18 T18 T18
T9
will illuminate when in
will illuminate when in
T6 T6
will illuminate which pin
will illuminate which pin
will illuminate which pin
T18 T18
ABN Test Clip leads to their
ABN Test Clip leads to their
T9
.
T13 T13 T13
T10 T10 T10
.
will
T4
T7 T7
5
Publicidad
