Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
POLARITY AND VOLTAGE PRESENCE TESTING
The Digital Toner-Pro may be used to test polarity and type of voltage present:
If testing via the RJ45 PORT
Test Leads, connect the Digital Toner-Pro's red
Test Leads, connect the Digital Toner-Pro's red
leads to their respective Test Lead Inputs
1. Connect the ABN Test Clips, or insert a cable into the RJ45 PORT
2. Turn Digital Toner-Pro on by pressing the Power On/Off button
3. Select Test Mode by pressing the Mode Button
Select Test Mode by pressing the Mode Button
Test Mode Indicator
4. Check the "CONT" Indicator
5. The "NRM" (Normal) Polarity Indicator
"NRM" (Normal) Polarity Indicator
is connected to the POTS (Plain Ol' Telephone Service) in the
is connected to the POTS (Plain Ol' Telephone Service) in the
is connected to the POTS (Plain Ol' Telephone Service) in the
Test Clip
T14 T14
proper orientation. The "REV" (Reverse) Polarity Indicator
if the wires are reversed.
• The "NRM" (Normal) Polarity Indicator
ABN Test Clip detects higher voltage than the red ABN Test Clip.
• The "REV" (Reverse) Polarity Indicator
ABN Test Clip detects higher voltage than the black ABN Test Clip.
• The "NRM" (Normal) Polarity Indicator and "REV" (Reverse) Polarity
Indicator will both illuminate when AC voltage is present.
• When the RJ11 Test Plug is used, the "NRM" (Normal) Polarity Indicator
will illuminate on a correctly wired and powered POTS (Plain Ol'
Telephone Service) phone jack.
NOTE: The POTS (Plain Ol' Telephone Service) color code convention
(black/positive, red/negative) is the opposite of the multimeter color
code convention (red/positive, black/negative).
RJ45 TERMINATED DATA CABLE WIRE MAP TESTING
1. Insert one end of the data cable to be tested into the RJ45 port
Digital Toner-Pro.
2. Insert the opposite end of the cable into the Digital Probe-Pro's RJ45 Port.
3. Enter MAPPING mode by pressing the MODE button
Enter MAPPING mode by pressing the MODE button
Indicators
T18 T18
into mapping mode when the toner is set to mapping mode.
4. A wire pin-to-pin map will be displayed on both the Toner and Probe. The
A wire pin-to-pin map will be displayed on both the Toner and Probe. The
Toner's Wire Map Indicators
which pin on the Toner end of the cable is being mapped. Simultaneously, the
Probe's Wire Map Indicators will illuminate to indicate which pin on the Probe
end of the cable is connected to the actively indicated pinout on the Toner end;
this enables detection of mis-wired cables and cable faults (for example, if pin
3 on the Toner end of the cable is connected to pin 6 on the Probe end of the
cable, when the Toner's #3 Wire Map Indicator illuminates, the Probe's #6
Wire Map Indicator will illuminate).
8
OPERATING INSTRUCTIONS
, proceed directly to step 2. If testing via the ABN
, proceed directly to step 2. If testing via the ABN
, proceed directly to step 2. If testing via the ABN
T21 T21 T21
is illuminated.
is illuminated.
T1 T1
T4
illuminate and blink. The Digital Probe-Pro will automatically go
illuminate and blink. The Digital Probe-Pro will automatically go
T18 T18
and black
T14 T14
.
T20 T20 T20
. If illuminated green, testing can proceed.
will illuminate if the red ABN
will illuminate if the red
T2
will illuminate when the black
will illuminate
T2
w will illuminate when the red
T3
will slowly blink in order 1 thru 8, to indicate
will slowly blink in order 1 thru 8, to indicate
ABN Test Clip
ABN Test Clip
T15 T15
T21 T21 T21
.
T9
repeatedly
repeatedly until the
repeatedly until the
repeatedly
T8 T8
will illuminate
will illuminate
T3
on the
on the
T21 T21 T21
until the Wire Map
until the Wire Map
T8 T8
.
Publicidad
