Publicidad
Idiomas disponibles
Idiomas disponibles
bottom edge of the previous spray so that the edges slightly overlap
to better cover the area being treated.
Thin layer
Thick layer
Thin layer
Do not work the spray gun unevenly as shown above.
Cleaning the device
Cleaning the spray gun
Note: Do not immerse the gun in detergent!
1. Unlock the fan assembly and remove it from the gun assembly. Align
the release latch and pull the gun out. Squeeze the trigger to release
any spray material in the gun in the tank.
2. Unlock and remove the reservoir to empty any residual spray material
in the reservoir. Pour into the original packaging.
3. Pour a little solvent into the tank for cleaning.
4. After washing the tank, the remaining fluid should be properly disposed
of to avoid environmental contamination.
5. Refill the reservoir with a new portion of solvent. Screw the reservoir of
the cleaning solution onto the gun.
6. Clean the nozzle in a safe area. Press the gun trigger for a few seconds
(2-5s) to allow the cleaning solution to clean the nozzle. After a while,
do this step again for a few seconds.
7. Then remove the reservoir and squeeze the trigger.
8. Wipe and clean the outside of the tank, remove the adjustment knob,
nut, nozzle guard, nozzle etc.
9. Clean the reservoir, nozzle guard, nut, nozzle, air flow regulator, gun
assembly, etc.
Note: Never use a sharp metal needle or similar objects to clean
the nozzles!
Never use a solvent or lubricant containing silicone to clean the
nozzles!
Don't overlook the nozzle seal.
10. Reassemble the dismantled parts after cleaning
11. If the battery is not used for a long time, it should be stored separately
(disconnected from the device).
After using the gun, check whether the filter is dirty or not. If it is too
dirty, you need to replace the filter in the following steps.
1. Take the battery out of the device and then remove the filter cover (11)
with a screwdriver.
2. Take out the dirty filter and replace it with a new one.
3. Then reinstall the filter cover (11).
Never use the spray gun without the filter!
Dust or other particles may be sucked into the device and damage
the device. Or get the solution on the treated surface
Troubleshooting
DESCRIPTION OF
GROUNDS
THE PROBLEM
Maintenance
SOLUTION
The solution is sprayed at
Clogged nozzle
a low flow rate or no
Suction tube clogged
escape
Flow regulator set for low capacity
The suction tube is not immersed
in the solution
The reservoir is not tightened
properly
The filter is clogged
The sprayed liquid drips
Nozzle loose
dropwise from the nozzle
Damaged nozzle
Damaged nozzle seal
The material being sprayed has
accumulated in the nozzle
Spraying the liquid is not
Too high viscosity of the sprayed
correct
liquid
High spray material flow
Flow regulator set too high
capacity
Clogged nozzle
Filter clogged
Variable
amount
of
Not enough spray material in the
sprayed material
tank
Filter clogged
The sprayed liquid will run
Too much liquid is sprayed
off the surface
Spray layer too thin
Too little solution delivered
Spray gun moving too quickly
LP
NAME OF THE ELEMENT
A
Spray part with nozzle and tank
B
Compressor unit
C.
Battery (not included)
D
A cup of stickiness
E.
Nozzle
F.
Sealing ring
G.
A special key
H.
A special needle to unscrew the nozzle
I
Brush
ENVIRONMENTAL PROTECTION
Electrically powered products should not be disposed
of with household waste, but should be disposed of in
appropriate facilities. Information on disposal can be
obtained from the dealer of the product or local
authorities. Waste electrical and electronic equipment
contains substances that are not neutral for the natural
environment.
potential threat to the environment and human health.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka
komandytowa with its registered office in Warsaw, ul. Pograniczna 2/4
(hereinafter: "Grupa Topex") informs that all copyrights to the content of
this manual (hereinafter: the "Manual"), including its text, photos,
diagrams, drawings, and its compositions belong exclusively to the Topex
Group and are subject to legal protection in accordance with the Act of
February 4, 1994, on copyright and related rights (i.e. Journal of Laws of
2006 No. 90 Item 631, as amended). Copying, processing, publishing,
modifying for commercial purposes the entire Manual and its individual
elements, without the consent of Grupa Topex expressed in writing, is
strictly prohibited and may result in civil and criminal liability.
WARRANTY AND SERVICE
The warranty conditions and the description of how to proceed in the event
of a complaint are included in the attached Warranty Card.
GTX Service Central ServiceNS. z o. o. Sp.k.
ul. Borderland 2/4
02-285 Warsaw
A network of Service Points for warranty and post-warranty repairs
available on the gtxservice.pl internet platform
Scan the QR code and visit gtxservice.pl
7
Clean the nozzle
Clean / unclog the suction
tube
Set the flow regulator to a
more efficient position
Check the suction tube
Tighten the reservoir
Replace the filter
Tighten the nozzle
Replace the nozzle
Replace the nozzle seal
Clean the nozzle
Dilute the spray material
Reducing the fluid flow rate
Change the setting of the flow
regulator
Clean the nozzle
Replace the filter
Fill the tank
Replace the filter
Reduce the solution flow rate
or move the spray gun faster
increase the flow rate of the
solution
Move the spray gun more
slowly
List of items
Non-recycled
equipment
tel. +48 22 364 53 50
e-mail
bok @ gtxservice.com
QUANTITY
1
1
1
1
1
1
1
1
1
poses
a
Publicidad
