Indesit UIAA 2 Y Serie Manual De Instrucciones página 23

Installation
! Before placing your new appliance into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the
appliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of
the appliance and any furniture above it, and at least 5 cm
between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat
(direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied in
the installation kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator
by tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical
socket ensure the following:
• The appliance is earthed and the plug is compliant with the
law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on
the bottom left side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values
indicated on the data plate located on the bottom left side
(e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use
extension cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
! The manufacturer declines any liability should these
safety measures not be observed.
Start-up and use
Starting the appliance
! After transportation of the appliance, carefully place it in an
upright position and wait at least 3 hours before connecting it to
the electricity mains, to make sure it operates as it should.
• Clean the inside of the refrigerator well using warm water
and bicarbonate of soda before placing food inside it.
• The appliance comes with a motor protection control system
which makes the compressor start approximately 8 minutes
after being switched on. The compressor also starts each
time the power supply is cut off whether voluntarily or
involuntarily (blackout).
Freezer Compartment
When the product is switched on the freezer compartment
is set to its default value of -18°C. We recommend that the
SUPER FREEZE function is set in order to accelerate the
cooling process of the compartment; when the inside of the
compartment has reached its optimal temperature the function
will be deactivated and the food may be placed inside.
Navigating the display
Setting the temperatures:
If the product is switched on, the refrigerator and freezer
compartment displays will indicate the temperature values
set at that moment. To change them, simply press the - and +
buttons corresponding to the compartment for which you wish
to change the set temperature. More specifically, each time the
buttons are pressed, the temperature increases or decreases
and the level of cold generated inside the compartment is
adjusted accordingly. The temperature values that may be
selected for the refrigerator compartment are +8°C, +7°C,
+6°C, +5°C, +4°C, +3°C and +2°C, while the values that may
be set for the freezer are -18°C, -19°C, -20°C, -21°C, -22°C,
-23°,-24°C,-25°, and -26°C. If SUPER FREEZE functions is
activated, Freezer temperature cannot be modified.
Using the freezer to its full potential
• Adjust the temperature using the display.
• Do not re-freeze food that is defrosting or that has already
been defrosted. These foods must be cooked and eaten
(within 24 hours).
• Fresh food that needs to be frozen must not come into
contact with food that has already been defrosted. Fresh
food must be stored in the top FREEZER and STORAGE
compartment where the temperature drops below -18°C and
guarantees rapid freezing.
• To freeze fresh food in the best and safest way possible,
activate the SUPER FREEZE function 24 hours before placing
the food in the freezer. After placing the food inside, activate
the SUPER FREEZE function again; it will be deactivated
automatically after 24 hours;
• Do not place glass bottles which contain liquids, and which are
corked or hermetically sealed in the freezer because they could
break.
• The maximum quantity of food that may be frozen daily is
indicated on the plate containing the technical properties
located on the bottom left side of the refrigerator compartment
(for example: Kg/24h: 4).
• In order to obtain a greater amount of space in the freezer
compartment, you may remove the bins (except the lowest
bin and the special COOL CARE ZONE bin, which has an
adjustable temperature) and place the food directly onto the
evaporator plates.
! If the room temperature drops below 14°C for an extended
period of time, the ideal temperature will not be reached in the
freezer compartment and food preservation will be reduced.
! Do not open the door during freezing.
! If there is a power cut or malfunction, do not open the freezer
door. This will help maintain the temperature inside the freezer,
ensuring that foods are conserved for at least 9 -14 hours.
*
Ice ice tray
3
The fact that they are situated on the top part of the freezer
drawers ensures greater cleanliness: the ice no longer
comes into contact with the food placed inside the freezer
compartment; furthermore, the dripping of the water during
filling is avoided (a lid to cover up the hole after filling with water
is also provided).
1. Pull out the tray by pushing it up. Check that the tray is
completely empty and fill it with water through the opening
provided.
2. Take care not to exceed the level indicated (MAX WATER
GB
23