Publicidad
Idiomas disponibles
Idiomas disponibles
6
IMPORTANT PARTS
Figures 1 & 2
1. A/D (Activate/Deactivate) Button
2. Outlet Port
3. Carrying Case
4. Air-Inlet Filter
5. Power Switch
6. AC Power Connector
7. DIN connector
8. Power Cord (assure proper configuration for outlet)
9. Service Required LED
ACCESSORIES/REPLACEMENT ITEMS
Figure 3
1. CPAP Humidifier ................................900HC105
Distributed by Sunrise Medical in the U.S. only.
2. Nasal Masks
Small..............................................9351D-668
Medium Small ..................................9351D-667
Medium ..........................................9351D-669
Large..............................................9351D-670
3. Air-Inlet Filter (4/pk) .......................8000D-602
Fine Particle Air-Inlet Filter
(not shown) (4/pk) ..........................8000D-603
4. Oxygen Adapter ...............................7353D-601
5. DeVilbiss Seal-Ring®
Small..............................................9351D-658
Medium ..........................................9351D-659
Large..............................................9351D-660
6. 6' 22 mm Tubing ..............................7351D-616
7. Strap-Style Headgear ........................7351D-617
8. Cap-Style Headgear ..........................7351D-627
9. DeVilbiss Humidifier................................9100D
10.Serenity™ Mask ......................................9352D
Replacement Cushion........................9352D-601
15mm Tubing Swivel.........................9352D-602
Mask Adapt O
Port ..........................9352D-603
2
Replacement Pads and Vent ...............9352D-604
Mask Headgear Strap/Mesh ................9352D-619
Serenity Mask w/out Headgear ...........9352D-621
Ask your Sunrise Medical provider for information about
other DeVilbiss mask styles and sizes.
A-854
I m p o r t a n t P a r t s
3
2
1
Figure 1
4
9
5
6
7
8
Figure 2
8
1
7
2
5
4
3
6
Figure 3
S e t - U p
SET-UP
This is not a life support device and is intended
to be used on spontaneously breathing adults.
NOTE– Refer to Important Parts for part identification.
• Place unit on level, sturdy surface away from
heating vents, radiators, drapes, and bedspreads
so that air intake is not restricted.
• Insert the appropriate power cord into the AC
power connector (Figure 2).
• Make sure the power switch is in the "Off" posi-
tion. Plug the power cord into an appropriate
wall outlet.
• Connect the 6-foot length of 22 mm diameter
tubing to the outlet port on the front of the unit
Figure 4. This is the port from which CPAP air
supply is provided.
• Connect the opposite end of the 22 mm tubing
to the mask and headgear assembly.
NOTE– Excess facial oils will deteriorate mask material.
To prolong mask life, wash face nightly before
wearing mask.
NOTE– Some tubing is prone to kinking. Flow can be
blocked causing apnea episodes to resume. Use
only 22 mm diameter smooth bore-type, kink-
resistant tubing.
• Position mask loosely on face. Adjust headgear
straps so mask is snug and comfortable Figure 5.
OPERATION
Step 1
• Press power switch (rear of unit) to the "On"
position. The blower will operate.
Step 2
• Your DeVilbiss AutoAdjust LT nasal CPAP device
will automatically adjust the CPAP pressure up
and down throughout the night based on your
needs. If you wake up and the pressure seems
too high, simply press the A/D button on the
front of the unit and the pressure will return to a
low pressure operating mode Figure 6.
Step 3
• Breathe into the mask and go to sleep.
7
Figure 4
Figure 5
Figure 6
A-854
Publicidad
