Publicidad
Idiomas disponibles
Idiomas disponibles
It is possible to activate special functions that vary the operation of the two relay outputs and other
functions such as: the deactivation of network failure signal on the relay, deactivate the liquid control,
activate a relay during firing, deactivation of the burner washing cycle, "Bistable" shot mood, burner
preheating (it is maintained at 50% of the operating temperature during the disarming, this to speed up the
resetting phase).
To access the programming menu of the special functions you need to:
1. Disconnect ARM and FOG
2. Note down the DIP-SWITCH configuration
3. Turn all DIP-SWITCH OFF
4. Remove the Jumper from BUZZ (J3)
5. Place the Jumper on J2
6.
T
urn ON all DIP-SWITCHES of the functions you want to be activated
7. Remove the Jumper from J2 and replace it on BUZZ (J3)
8. Restore the DIP-SWITCH as noted down before (point 2)
220V LACK SIGNALING
LIQUID LEVEL CONTROL
"STATE" OUTPUT LOGIC
"LEV" OUTPUT LOGIC
LIQUID / SHOT RELAY
CONFIGURATION
PUMP SAVE
WASH POST- SHOT
BISTABLE SHOT
(ON-OFF)
PREHEATING OF THE BOILER
AT 50%
Note: Activating the "SAVE-PUMP" function automatically activates the "WASH at the end of firing" function. The
"Washing" function, on the other hand, is automatic, but if it is deactivated, it also excludes the Save-Pump function.
EVERY TIME YOU ENTER IN THIS MENU, THE SPECIAL FUNCTIONS ARE RESTORED TO THE FACTORY
VALUES, so if for example we have used 2 special functions and we have changed our mind on one of
these, entering in the menu again we will only need to reactivate the function that we intend keep (the
other one will be deactivated automatically)
SPECIAL FUNCTIONS - MENU 1
(
POWERED DEVICE - J2 CLOSED - ALL DIP OFF - NO ARM )
DIP1
DIP2
DIP3
OFF
X
X
ON
X
X
X
OFF
X
X
ON
X
X
X
OFF
X
X
ON
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DIP4
DIP5
DIP6
DIP7
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
OFF
X
X
X
ON
X
X
X
X
OFF
X
X
X
ON
X
X
X
X
OFF
X
X
X
ON
X
X
X
X
OFF
X
X
X
ON
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
CAUTION!!!
14
DIP8
DIP9
X
X
LACK OF 220V SIGNALED IN THE
STATE RELAY
LACK OF 220V NOT SIGNALED IN
X
X
THE STATE RELAY
LIQUID LEVEL CONTROL ACTIVE
X
X
X
X
LIQUID LEVEL CONTROL DISABLE
X
X
RELE N.O.; CLOSED IF ARMED AND
WITHOUT FAILURES
X
X
RELE N.O.; CLOSED IF THERE ARE
FAILURES
RELE N.C.; OPEN WHEN THE
X
X
LIQUID IS MISSING
RELE N.O.; CLOSED WHEN THE
X
X
LIQUID IS MISSING
X
X
RELAY USED AS LIQUID SIGNALING
RELE N.O.; CLOSED WHEN THE
X
X
SHOT IS IN FUNCTION
PUMP SAVE FUNCTION OFF
X
X
X
X
PUMP SAVE FUNCTION ON
WASH POST-SHOT - OFF
X
X
X
X
WASH POST-SHOT - ON
AUTOMATIC SHOOTING TIME
OFF
X
ACCORDING TO SETUP DIP 9/10
ON
X
MANUAL SHOOTING TIME
X
OFF
50% PRE-HEATING FUNCTION
DISABLED
X
ON
50% PRE-HEATING FUNCTION
ENABLED
SETTING
Publicidad
