Cub Cadet 19A30056100 Manual Del Operador página 6

NOTE: References to left, right, front and rear of the tractor are from the operator's position,
unless otherwise stated.
• Before assembly, place the tractor on a firm, level surface, disengage the
PTO, stop the tractor engine and set the parking brake.
Tools Required
• 1/2" wrench or socket
• 7/16" wrench or socket
Assemble Mounting Brackets
To build the bagger mounting
assembly, locate the mounting
assembly pack and follow these
steps:
1. Attach the two hitch side
brackets to the universal
support bracket (783-
08129) using two carriage
bolts (710-0276) and wing
knobs (720-04122) from
hardware pack 689-02364.
See Figure 1.
NOTE: The hooks on the
side brackets should point
downwards and the tabs on
the rear plate point upwards as
shown in Figure 1.
2. Flip over assembly and
mount the hitch support
bracket to the mounting
assembly with two wing
knobs as shown in Figure 2.
NOTE: During the mounting
stage it is recommended to
leave this hardware only finger
tight to facilitate lining up
the hitch hole for the clevis
pin. You will be instructed to
tighten this hardware later in
this manual.
Mount Assembly on
Tractor
1. Place the hooked ends of
the mounting assembly
over the shoulder bolts
on the tractor and line up
the hitch support bracket
center hole with the hole
on the tractor's hitch. See
Figure 3.
2. Install the support bracket
(783-08856), included
with the loose parts, into
the mounting assembly as
shown in Figure 4. Line the
holes up as shown.
NOTE: The support bracket is not intended for units with a differential lock
transmission.
ASSEMBLY & INSTALLATION
3.
4.
Figure 1
Mount Vertical
Support
1.
2.
Use this
mounting hole
3.
Figure 2
Install Hanger
Assembly
1.
Figure 3
6
Install the clevis pin (711-
0309A) from hardware
pack 689-02364 into the
tractor's hitch, the support
bracket, and the mounting
assembly and secure with
a cotter pin (714-0117).
See Figure 4.
Install the bracket,
785-08856, as shown in
Figure 4, by using the
bolt, nut, and washer
from hardware pack
689-02835. Slot the bolt,
710-0376, into hole A then
place the washer, 736-0159, and nut, 712-04063, onto the bolt from the
inside of the hitch.
NOTE: The clevis pin can be fed down through the hitch plate and secured
underneath with the cotter pin, or it may be easier to feed the clevis pin up through
the hitch plate hole and secure with the cotter pin on the topside. The clevis pin
has two holes. It is recommended to use the hole closest to the head of the pin for a
tighter connection.
IMPORTANT! If you decided to leave the hitch support only finger tight during the
assembly process, tighten all of the hardware securely at this time.
Install the vertical
support onto the
mounting assembly of the
tractor by hooking it over
the hitch plate.
Align the left hole on the
vertical support with the
farthest left hole. See
Figure 5.
new bracket. 50/54 location.
Secure the vertical
support to the mounting
assembly using a carriage bolt (710-0276) and a wing knob (720-04122)
from hardware pack 689-02364. Refer to Figure 5.
NOTE: Some kits may contain cross-mount brackets with numerical identification
over the holes instead of letters as shown. If this is the case, use the hole
corresponding to the deck size the bagger is being installed on.
Install and secure
the hanger assembly
(683-04498B) to the
vertical support using
two carriage bolts (710-
0276), two cup washers
(736- 0242) and two
lock nuts (712-04063)
from hardware pack
689-02364. Do not
overtighten. See Figure 6.
Figure 4
Figure 5
1
1
2
2
2
Figure 6