Publicidad
Idiomas disponibles
Idiomas disponibles
smooth surface
equal length
2.2.2. Operation
Introduction for buttons on remote controller
Note:
• This is a general use remote control. It can be used for various multifunction air
conditioners; If a button on the remote control is pressed for a function that is
not available on a particular model, the unit will maintain its current running
status.
• When power is switched on (stand by condition), you can operate the air
conditioner through the remote control.
• When unit is on, each time you press the button on the remote control, the
sending signal icon " " on the remote control display will blink once. If the air
conditioner emits a beep sound, it means the signal has been sent.
• When unit is off, Set temperature will be displayed on the remote control (If
the light of indoor unit display is turned on, the corresponding icon will be
displayed);
When unit is on, it will display the icon of the current function.
ON/OFF button
Press this button to turn unit on/off.
MODE button
Press this button once to cycle through the modes and select the one required as
shown below (the corresponding icon "◄" will be lit up after the mode is selected):
AUTO ►COOL ►DRY ►FAN ► HEAT (Only for models with heating function)
• When auto mode is selected, the air conditioner will operate automatically
according to ambient temperature. Set temperature can't be adjusted and
won't be displayed either. Press FAN button to adjust fan speed.
• When cool mode is selected, the air conditioner will operate in cool mode. Then
press + or - button to adjust Set temperature. Press FAN button to adjust fan
speed.
• When dry mode is selected, the air conditioner will operate at low fan speed in
dry mode. In dry mode, the fan speed can't be adjusted.
• When fan mode is selected, air conditioner will operate in fan mode only. Press
the FAN button to adjust fan speed.
20
G305MA_AF1_AC9_indoor_170216.indd 20-21
improper expanding
leaning
damaged
crack
uneven
surface
thickness
• When heat mode is selected, the air conditioner will operate in heat mode.
Then press + or - button to adjust Set temperature. Press the FAN button to
adjust fan speed.
(The cooling only unit can't receive the HEAT mode signal. If HEAT mode is
set by the remote control, press ON/OFF button if you can't turn on the air
conditioner.)
+ / - Button
• Pressing + or - button once will increase or decrease Set temperature by 1°F
(°C).
Hold + or - button for 2s, Set temperature on the remote control will change
quickly.
Release the button after your required Set temperature is reached.
• When setting Timer On or Timer Off, press the + or - button to adjust the time.
(See TIMER Button for setting details)
FAN button
Pressing this button can select fan speed circularly as: AUTO, SPEED 1 (
(
), SPEED 3 (
), SPEED 4 (
) .
Note:
• In Auto speed, air conditioner will select the proper fan speed automatically
according to the ambient temperature.
• Fan speed can't be adjusted under Dry mode.
SWING button
Press this button to turn on up & down air swing.
SLEEP button
In Cool, Heat and Dry modes, press this button to turn on Sleep function. Press this
button to cancel Sleep function. In Fan and Auto mode, this function is unavailable.
TIMER button
• When unit is on, press this button to set Timer Off. The T-OFF and H icons will be
blinking. Within 5s, press + or - button to adjust the time for Timer Off. Pressing
the + or - button once will increase or decrease the time by 0.5h. Holding + or –
button for 2s, will change the time more quickly. Release the button when your
required set time is reached. Then press the TIMER button to confirm it. The
T-OFF and H icon will stop blinking.
• When unit is off, press this button to set Timer On. The T-ON and H icons will
be blinking. Within 5s, press the + or - button to adjust the time for Timer On.
Pressing the + or - button once will increase or decrease the time by 0.5h.
Holding the + or – button for 2s, will change the time more quickly. Release the
when your required set time is reached. Then press TIMER button to confirm it.
The T-ON and H icons will stop blinking.
• Cancel Timer On/Off: If the Timer function is set up, press the TIMER button
Split Air Conditioner | Aire acondicionado Split | Ar condicionado Split
EN
), SPEED 2
21
17.02.16 18:51
Publicidad
