Becken BAC2321 Manual De Instrucciones página 13

Clean filter
1. Open panel
Pull the panel out to a certain angle
as shown in the figure.
3. Clean filter
Use dust catcher or water to clean the filter.
When the filter is very dirty, use water
(below 45ºC) to clean it, and then put it in a
2
shaded and cool place to dry.
• The filter should be cleaned every three months. If there is a lot of dust in the
operation environment, the frequency of cleaning can be increased.
• To avoid injury, do not touch the fins after removing the filter.
• To avoid deformation or fire hazard, do not use fire or a hair dryer to dry the
filter.
NOTICE: Checking before seasonal use
1. Check whether air inlets are blocked.
2. Check whether air switch, plug and socket are in good condition.
3. Check whether the filter is clean.
4. Check whether drainage pipe is damaged.
NOTICE: Checking after seasonal use
1. Disconnect power supply.
2. Clean indoor unit's filter and panel.
2.4. Troubleshooting
General phenomenon analysis
Please check the items below before asking for maintenance. If the malfunction still
can't be eliminated, please contact a local dealer or qualified professional.
24
G305MA_AF1_AC9_indoor_170216.indd 24-25
2. Remove filter
Remove the filter as indicated in the
3
figure.
4. Install filter
Install the filter and then close the panel
cover tightly.
4
Phenomenon Check items
Is it experiencing severe
interference (such as from static
electricity or unstable voltage)?
Is the remote control within the
signal receiving range?
Are there any obstacles?
Is the remote control pointing
at the receiving window?
Indoor unit can't
receive remote control's
signal or remote control Does the remote control have
low; sensitivity, fuzzy display, or
is inactive.
no display?
No display when operating
remote control?
Fluorescent lamp in room?
Indoor unit's air inlet or outlet
is blocked?
If in heating mode, has the
indoor temperature reached
No air emitted from
the set temperature?
indoor unit
Has heating mode just been
turned on?
Power failure?
Is the plug loose?
Air switch trips off or fuse is
blown?
Air conditioner can't
Wiring has a malfunction?
operate
Unit restarts immediately after
stopping operation?
Is the function setting on the
remote control correct?
Is there high indoor
Mist is emitted from temperature and humidity?
indoor unit's air outlet
Is unit operating in auto mode?
Set temperature can't
be adjusted
Your required temperature
exceeds the set temperature
range?
Voltage is too low?
Filter is dirty?
Cooling (heating) effect
is not good.
Is Set temperature within the
proper range?
Door or window are open?
Split Air Conditioner | Aire acondicionado Split | Ar condicionado Split
EN
Solution
Pull out the plug. Reinsert the plug after
about 3min, and then turn the unit on
again.
Signal receiving range is 8m.
Remove obstacles.
Select proper angle and point the
remote control at the receiving window
on the indoor unit.
Check the batteries. If the battery
power is too low, please replace them.
Check whether remote control appears
to be damaged.
If yes, replace it.
Move the remote control closer to
indoor unit.
Turn off the fluorescent lamp and then
try it again.
Eliminate obstructions.
After reaching to set temperature, the
indoor unit will stop blowing out air.
In order to prevent blowing out cold air,
the indoor unit will only be started after
several minutes delay. This is a normal
phenomenon.
Wait until power is restores.
Reinsert the plug.
Ask a professional to replace the air
switch or fuse.
Ask a professional to replace it.
Wait for 3min, and then turn the unit
on again.
Reset the function.
This is due to the indoor air being
cooled rapidly. After a while the indoor
temperature and humidity will decrease
and the mist will disappear.
Temperature can't be adjusted in auto
mode.
Please switch the operating mode if you
need to adjust the temperature.
Set temperature range:
16°C ~30°C.
Wait until the voltage returns to
normal.
Clean the filter.
Adjust temperature to within the
proper range.
Close doors and windows.
25
17.02.16 18:51