Kärcher B 110 R Classic Bp D75 Manual Del Usuario página 15

Fresh water tank cap with fresh water filter
1
Coarse dirt filter
2
Waste water tank cap
3
Control panel
4
Squeegee blade adjustment wheel (D cleaning
5
head only)
Brush replacement pedal
6
Steering wheel
7
Side skirts
8
*Battery
9
Type plate
10
Seat adjustment lever
11
Storage area for "Homebase Box" cleaning set
12
*Warning light
13
Seat
14
Waste water tank latch
15
Fresh water tank filling hole
16
Hose holder
17
Daytime running light
18
Accelerator pedal
19
Float
20
Fluff filter
21
Waste water tank drain hose
22
Waste water tank
23
* Mop holder
24
Suction hose
25
Suction bar clamping lever
26
Waste water tank cap
27
Suction bar
28
Cleaning head
29
Fresh water filling level indicator
30
Fresh water tank
31
* optional
Colour coding
● Control elements for the cleaning process are yel-
low.
● Control elements for maintenance and servicing are
light grey.
Control panel
Horn
1
Travel direction switch
2
Program switch
3
Intelligent Key
4
*Display
5
Info button
6
Safety switch
7
*Disturbances in the symbols on the display can be
caused by the influence of electromagnetic devices
such as mobile phones, but have no effect on the oper-
ating behavior.
Program switch
OFF
1
Device is switched off.
TRANSPORT MODE
2
Drive to the operating location.
ECO MODE
3
Clean the floor wet (with a reduced amount of water
and a reduced brush speed) and vacuum up waste
water (with reduced suction power).
NORMAL MODE
4
Clean the floor wet and vacuum up waste water.
HEAVY MODE
5
Clean the floor wet (with increased brush contact
pressure) and vacuum up waste water.
SCRUB MODE
6
Precleaning without vacuuming
Clean the floor wet and let the detergent act.
SUCTION MODE
7
Vacuum up the dirty waste.
POLISH MODE
8
Polish the floor at a high brush speed without apply-
ing liquid.
Symbols on the device
Fresh water tank drain opening
Waste water tank drain opening
Fresh water tank filling level (50%)
Lashing point
* Mop holder
Brush replacement
* optional
Installation
Unloading
1. Remove the packaging film.
2. Remove the strap.
Strap
1
Board
2
Block
3
English
Beam
4
3. Unscrew the block, squared timber and boards. The
components to be unscrewed are marked in grey in
the figure.
4. Place a ramp in front of the pallet with the un-
screwed boards and squared timber and fasten with
chipboard screws.
5. Install the batteries if the device was delivered with-
out batteries (see chapter "Before inital startup/ bat-
teries").
6. Drive the device forward and off the pallet (see
chapter "Operation / Driving").
Installing the brushes
1. The installation of the brushes is described in the
chapter "Maintenance work".
Installing the suction bar
1. Pivot both clamping levers upwards.
Suction hose
1
Suction bar suspension
2
Suction bar
3
Clamping lever
4
2. Insert the suction bar in the suction bar mount.
3. Pivot both clamping levers downwards.
Batteries
Installing and connecting batteries
CAUTION
Removing and installing the batteries
Unstable machine position
Ensure that the machine is positioned stably when re-
moving and installing the batteries.
ATTENTION
Incorrect connection polarity
Destruction of the control electronics
Take care to ensure the correct polarity when connect-
ing the batteries.
ATTENTION
Deep discharge
Risk of damage
Charge the batteries before starting the device.
1. Drain the waste water.
2. Unlock the waste water tank and pivot it up.
3. Disconnect the seat switch and remove the seat.
4. Place the battery in the device.
5. Connect the device-side battery connector to the
battery-side battery connector.
6. Reset the seat and connect the seat switch.
7. Pivot the waste water tank forwards and close it.
Removing the battery
CAUTION
Removing and installing the batteries
Unstable machine position
Ensure that the machine is positioned stably when re-
moving and installing the batteries.
1. Set the safety switch to "0".
2. Drain the waste water.
3. Unlock the waste water tank and pivot it up.
4. Pull out the battery plug.
15