Publicidad
Idiomas disponibles
Idiomas disponibles
Malfunction
The device cannot be started
The device is no longer running, dis-
play shows "battery empty"
The device moves unevenly (jerks)
when starting and stopping.
The water volume is insufficient
The fresh water display shows the
wrong filling level after emptying the
tank manually.
The bar of the filling level display is
flashing, "fresh water empty" display
The suction performance is too low
The cleaning results are unsatisfacto-
ry
The brushes do not rotate
The device does not brake
The waste water drain hose is clogged 1. Open the dosing unit cover at the drain hose.
Warranty
The warranty conditions issued by our sales company
responsible apply in all countries. We shall remedy pos-
A: Packaging unit, B: Quantity required by the device
Description
Roller brush, red (medium, standard)
Roller brush, white (soft)
Roller brush, orange (high / low)
Roller brush, green (hard)
Roller brush, black (very hard)
Microfiber roller
Pad roller shaft
Roller pad, yellow (soft)
Roller pad, red (medium)
Roller pad, green (hard)
A: Packaging unit, B: Quantity required by the device
Description
Disc brush, natural colour (soft)
Disc brush, white
20
Malfunctions without information shown on the display
Rectification
1. Sit in the driver's seat.
2. Take your foot off the accelerator before switching on the safety switch.
3. Turn the safety switch to "1".
4. Check the battery and charge if necessary.
5. Set the programme switch to "OFF".
6. Wait 10 seconds.
7. Set the program switch to the desired program.
8. If possible, only drive the device on level ground.
9. Check the parking brake if necessary.
If the fault still occurs, call Customer Service.
1. Set the programme switch to "OFF".
2. Wait 10 seconds.
3. Set the program selector switch to "TRANSPORT MODE".
4. Drive to the charging station.
5. If the device still does not run, charge the battery on site or unlock the brake (see "Operation/pushing the device") and push
the device to the charging station.
1. Unlock the brake lock (see "Operation/pushing the device").
1. Check the fresh water filling level, if necessary fill the tank completely so that the air is pressed out.
2. Remove and clean the fresh water filter.
3. Insert the filter and screw on the cap.
4. Check the hoses for clogging and clean if necessary.
1. Use the device. During operation, the hose system will vent and the filling level display will correct itself.
1. Refill the fresh water tank.
1. Clean the seals between the waste water tank and the cover, check for leaks and replace if necessary.
2. Check the fluff filter for soiling and clean if necessary.
3. Clean the suction lips at the suction bar, turn over or replace if necessary.
4. Close the lid on the waste water drain hose.
5. Close the cover of the waste water tank rinsing system.
6. Check the suction hose for clogging and clean if necessary.
7. Check the suction hose for leaks and replace if necessary.
8. Check the adjustment of the suction bar.
1. Set the appropriate cleaning program for the cleaning task.
2. Use suitable brushes for the cleaning task.
3. Use a suitable detergent for the cleaning task.
4. Reduce the driving speed.
5. Adjust the contact pressure.
6. Adjust the squeegee blades.
7. Check the brushes for wear and replace if necessary.
8. Check the water output.
1. Reduce the contact pressure.
2. Check if the brushes are blocked by a foreign body and remove the foreign body if necessary.
3. If the motor is overloaded, let the motor cool down.
4. Set the programme switch to "OFF".
5. Wait 10 seconds.
6. Set the program switch to the desired program.
7. Check that the plug of the device is plugged into the cleaning head.
1. Undo the brake lock (see "Operation / Pushing the device").
2. Pull the suction hose off the suction bar and close it by hand.
3. Set the programme switch to "Vacuum".
The blockage is sucked out of the drain hose into the waste water tank.
sible malfunctions on your device within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
Cleaning head with roller brush accessories
R 75
Description
Part no.
4.035-605.0
For maintenance cleaning of heavily soiled floors.
6.907-771.0
For polishing and maintenance cleaning of sensitive floors.
6.907-730.0
For scrubbing structural floors (safety tiles, etc.).
6.907-731.0
For basic cleaning of heavily soiled floors and for coating removal (e.g. waxes, acrylates). 1
6.907-732.0
4.114-007.0
For maintenance cleaning of smooth floors.
4.762-627.0
For holding roller pads.
6.369-454.0
For polishing floors
6.369-456.0
For cleaning lightly soiled floors.
6.369-455.0
For cleaning normal to heavily soiled floors.
Cleaning head with disc brushes accessories
D 75
Description
Part no.
4.905-020.0
For polishing floors.
4.905-019.0
For polishing and maintenance cleaning of sensitive floors.
Accessories
English
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
A
B
1
2
1
2
1
2
2
1
2
1
2
1
2
20
96; 106
20
96; 106
20
96; 106
A
B
1
2
1
2
Publicidad
