Publicidad
Idiomas disponibles
Idiomas disponibles
English
brush assembly
36
and press firmly to ensure it is
secured in position.
6. Reinstall the rotary brush
the floor head
14
by aligning the keyed end of the
rotary brush
34
or soft beater bar
located in the floor head
7. Align the squared end of the rotary brush assembly
with the square slot on the floor head
8. Press firmly in the position shown indicated by arrows
on the squared end on the rotary brush assembly
to secure it into the floor head
an audible click as the release latch
locked position.
Removing and Installing the
Edge Brushes (Fig. S)
1. Locate the edge brush screw
2. Use a cross head screwdriver to remove the edge brush
screw
37
to release the edge brush
3. Pull the edge brush
4. Wipe away any dust of debris on the edge brush
5. Reinstall the edge brush
the slot on the side of the floor head
6. Press firmly into place and install the edge brush
screw
37
and use a cross head screwdriver to
tighten the screw into position.
7. Gently tug on the edge brush
securely in place before using.
Removing and Cleaning the Pet Head
Beater Bar (Fig. T)
1. To remove the beater bar
press the release button
2. The beater bar
can now be removed.
39
nOTE: The end pieces are also removable allowing you
to clear the brushes from any hair or other debris that
may have accumulated.
3. Wash the beater bar with warm soapy water.
4. Once the beater bar
39
the beater bar
39
into the pet head
firmly into position.
Troubleshooting
if the product does not work, check the following:
Unit will not start
•
Battery pack not charged.
•
Check battery pack charging requirements.
Battery pack will not charge
•
Charger not plugged in.
Plug charger into a working outlet. Refer to Important
•
Charging Notes for more details.
•
Surrounding air temperature too hot or too cold.
•
Move charger and battery pack to an area above
39 ° F (4 °C) or below 104 ° F (+40 °C).
12
34
or soft beater bar
21
with the gear
14
.
14
.
14
. Ensure you hear
35
snaps into its
37
.
15
.
15
away from the floor head
15
by aligning the shaft into
14
.
15
to ensure it is held
39
from the pet head
38
as shown in Fig. T.
is clean and completely dry, insert
20
until it clicks
if vacuum performance is poor, check the following:
Empty the dust bowl. (See Cleaning and Emptying the
•
vacuum section.)
21
into
Clean the filters. (See Cleaning and Emptying the
•
vacuum section.)
Clean the rotary brush. (See Removing and Cleaning the
•
36
Rotarty Brushes section.)
if rotator brush stops working, check the following:
•
Obstrustion - The unit is equipped with a rotary brush
36
overload feature. (See Removing and Cleaning the
Rotarty Brushes section.)
•
Rug or thick pile carpet - The unit is equipped with
a rotary brush overload feature. Rugs and carpet with
very thick and/or loose pile, can cause the overload
feature to activate and the rotary brush will stop rotating.
Try cleaning on the hard floor speed setting
problem persists, the surface is not suitable for cleaning
with the rotary brush.
Safe Storage (Fig. E)
14
.
WARNING:
unit with the rear of the vacuum facing a wall so that
any inadvertent fall of the unit would contact a wall
and not people or pets.
The unit can be safely stored, when not in use, by placing
the catch on the rear of the motor unit onto the charging
station
22
Accessories
WARNING:
20
,
those offered by BLACK+DECKER, have not been tested
with this product, use of such accessories with this
product could be hazardous. To reduce the risk of injury,
only BLACK+DECKER recommended accessories should
be used with this product.
Recommended accessories for use with your product
are available at extra cost from your local dealer or
authorized service center. If you need assistance in locating
any accessory, please contact BLACK+DECKER. Call
1‑800‑544‑6986.
Replacement Filter
The filter should be replaced every 6 to 9 months and
whenever worn or damaged. Replacement filters are
available from your BLACK+DECKER dealer.
Visit www.blackanddecker.com to locate dealers.
Replacement BlACK+DECKER filters: BHFEBF1
BHFEBF2
6
When not in use position the
as shown in Fig. E.
Since accessories, other than
.
2
. If the
31
and
Publicidad
