Important Safety Instructions; Functional Description - Makita DML184 Manual De Instrucciones

ENGLISH
1. Battery
2. Battery Release Button
3. Red Area
4. Fluorescent Tube
5. Lamp Cover
6. Screw Ring
SPECIFICATIONS
Fluorescent tube
Dimensions
(Without battery
cartridge)
Standard battery cartridge
Net weight
Rated voltage
• Due to our ongoing research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
IMPORTANT SAFETY
INSTRUCTIONS
WARNING:
When using electric tools, basic safety precautions should
always be followed to reduce the risk of fire, electric
shock, and personal injury. Some basic safety precautions
are as follows:
READ ALL INSTRUCTIONS.
1. Read this instruction manual and the charger
instruction manual carefully before use.
2. This Job site light is not waterproof. Do not use it in
damp or wet locations. Do not expose it to rain or
snow. Do not wash it in water.
3. A short-circuit can cause a large current flow,
overheating, possible burns and even damage.
(1) Do not touch the inside of the Job site light with
tweezers, metal tools, etc.
(2) Do not touch the battery terminals with any
conductive material.
(3) Avoid storing the battery in a container with any
metal objects such as nails, coins, etc.
4. Never expose the battery to flames, fire or significant
heat. Breakage may cause release of dangerous
material.
5. If battery chemicals get into your eyes, rinse them out
with water and seek medical attention right away. It
may result in loss of your eyesight.
6. If operating time has become excessively shorter, stop
operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
4
7. Switch
8. Strap Hook
9. Strap
10. Loosen
11. Tighten
12. Flourescent Tube Cap
Model
Bulb
Hook is lengthened
(L × W × H)
Hook is compressed
(L × W × H)
Diagram Legend
450 mm × 95 mm × 78 mm
(17-3/4" × 3-3/4" × 3-1/16")
370 mm × 95 mm × 78 mm
(14-9/16" × 3-3/4" × 3-1/16")
BL1430/
BL1415/
BL1440/
BL1415N
BL1450
0.72 kg 0.92 kg
(1.6 lbs) (2.0 lbs)
D.C. 14.4 V
7. Be careful not to drop, shake or strike the battery.
8. When the tool is not in use, always switch off and
remove the battery from the tool.
9. Do not store the tool and battery in locations where
the temperature may reach or exceed 50°C (122°F).
10. Do not give the tool a shock by dropping, striking, etc.
11. Do not expose the light to eyes continuously. It may
hurt them.
12. Do not cover or clog the lit tool with cloth or carton,
etc. It may create a risk of starting a fire.
13. Switch off the light immediately when the lamp light is
low. If you leave the lamp switched on, the battery
capacity may decrease.
14. Do not disassemble the charger or battery; take it to a
qualified serviceman when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock or fire.
15. If any problem develops, consult your nearest Makita
Service Center or dealer. Maintenance or repairs
should be carried out by Makita Authorized Service
Centers to maintain product safety and reliability.
16. If you notice that the tool is hot or is not functioning
correctly, consult your nearest Makita Service Center
or dealer.
SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

Charging
Charge the battery with the Makita charger before use.
13. Flashlight Cover
14. Flashlight Bulb Holder
15. Flashlight Bulb
16. Rings for Strap Clip Attachment
17. Metal Strap Clip
18. Metal Hang Hook
DML184
Compact FL13 W
18 V 0.2 A
BL1815/
BL1815N/
BL1820
0.78 kg
(1.7 lbs)
D.C. 18 V
BL1830/
BL1840/
BL1850
1.03 kg
(2.3 lbs)