Descargar Imprimir esta página

cecotec HYDROBOOST 1700 CAR&BIKE Manual De Instrucciones página 35

Hidrolimpiadora

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 29
ENGLISH
a direct jet on surfaces susceptible to damage. Avoid spraying windows with the direct jet, as
they may break.
The best way to avoid damaging surfaces is to follow these steps:
1. Before pressing the trigger, move the spray nozzle to the fan spray position.
2. Follow the distance and angle instructions mentioned above.
3. Vary the angle of the jet, the type of jet, and the distance from the surface to be cleaned
until efficient cleaning is achieved without damaging the surface.
Accessories
3D TurboFlip nozzle
The 3D TurboFlip nozzle, also defined as a rotating nozzle, is a very effective accessory to
significantly reduce cleaning time. It must be used to clean in the turbo mode explained in the
previous section. This accessory is assembled in the wand.
Soap bottle
This model includes an accessory to apply soap while operating. The use of soaps may reduce
the cleaning time and make the dirt removal easier. Some soaps have been designed for their
use in pressure washers and specific cleaning tasks. The use of thick soaps, like the soap used
with tableware, can clog the injection system with chemical products.
Warning
Soaps work better when applying them on the spray mode.
The chemical action combined with high-pressure rinses, in the concentrated mode, is very
effective. In vertical surfaces, apply soap from bottom to top. This will prevent soap from
falling and creating stains. High-pressure rinses can also be carried out from bottom to top.
With stains especially difficult to remove you may need to use a brush along with soap and
high-pressure rinses. Follow the instructions in the next section to use this accessory. Fig. 9
Anti-impurities filter
This model includes a transparent male connector with a filter which can be assembled with
the hose to prevent the dust from passing. This accessory is assembled in the water outlet (6).
360Brush special for wheel rims
This model includes a specific brush for car rims made of bristles, which can remove the
harshest dirt. When using this accessory, water will automatically come out as low-pressure
spray. This accessory is assembled in the gun.
68
HYDROBOOST 1700 CAR&BIKE
Original manual translation
EasyClean brush special for gaskets
This model also includes a cleaning brush which, combined with water and soap, helps remove
stains and allows for a more efficient cleaning. When installing and using this accessory, water
will automatically come out as spray, at low pressure. This accessory is assembled in the gun.
Cleaning process
The following cleaning procedure will help you organise and ensure you get the best results.
Remember to follow the previous advice.
Preparing the surface
-
Clear the area of furniture and check that windows and doors are securely closed.
-
Also make sure that plants and trees near the area to be cleaned are protected with a cloth.
Initial high-pressure rinse
Spray the area to be cleaned with water to clean any dirt that may have accumulated on the
surface. Before pressing the trigger, move the spray nozzle to the spray mode position and
progressively move it to the desired spray position. In this way, you will avoid applying an
excessively direct jet on more delicate surfaces.
Use of soap
Water and soap must be used with these percentages: 5.4% soap, 94.6% water (1:19).
Warning
Use only soaps designed for pressure washers.
-
Test the soap in an inconspicuous place before using the product.
-
Loosen the cap of the soap bottle and fill it with water and soap.
-
Replace the cover.
-
Disassemble the wand from the gun.
-
Install the soap bottle in the gun. Fig. 10
-
Apply soap in a manner that it covers all the surface to be cleaned. Apply it from bottom to
top to avoid soap from falling and staining the surface.
-
Leave the soap to act on the surface for several minutes. However, in particularly soiled
areas, use a brush to scrub gently. Do not allow soap to dry on the surface.
-
Remove the soap bottle from the gun and replace it with the wand and spray nozzle or
accessory to be used.
-
Rinse the soap from the surface.
Note: rinse the soap bottle with clean water after every use.
ENGLISH
69
HYDROBOOST 1700 CAR&BIKE

Publicidad

loading

Este manual también es adecuado para:

05718