cecotec CAFELIZZIA 790 STEEL PRO Manual De Instrucciones página 19

ENGLISH
- Portafilter
- Measuring spoon with tamper
- Instruction manual
First cleaning
- Fill the water tank with water. The water level should not exceed the "MAX" mark in the
tank.
- Put the filter in the filter holder and insert the portafilter. Ensure the portafilter is aligned
with the lock symbol to ensure it is safely assembled. Fig. 2.
- Plug the appliance into a power supply and press the power button. The machine will beep.
The 1-coffee and 2-coffee indicator lights will turn on, and the coffee machine will start
preheating.
- Once the 1-coffee and 2-coffee indicator lights light up steady, press the 1-coffee button.
The coffee machine will start the cleaning process. Make sure the steam knob is in the Off
position. Otherwise, the 4 indicator lights will stay turned on and the coffee machine will
not work.
Note:
If you want to carry out a more thorough cleaning cycle of the coffee machine's inside parts,
use a 1:4 solution of vinegar and water, or use descaling product. Repeat this process just with
water to remove any residue.
3. OPERATION
- Fill the water tank without exceeding the MAX mark.
- Connect the coffee machine to a power supply and make sure the steam knob is set to the
Off position.
Espresso
- While the coffee machine preheats, place the desired coffee filter in the portafilter and fill
it with coffee powder. Use the measuring spoon with tamper to fill the filter with coffee
and press it. 1 tablespoon is equal to 1 coffee dose. Clean the excess coffee from the filter's
edge. Fig. 3.
- Insert the portafilter in the appliance and lock it tightly. Fig. 4.
- Once the 1-coffee and 2-coffee light indicators switch from blinking to steady, press the
desired coffee button for the machine to brew 1 or 2 coffees.
Note
:
Make sure you have previously placed an appropriate cup or cups under the coffee spout.
36
CAFELIZZIA 790 STEEL PRO/SHINY PRO/WHITE PRO/BLACK PRO
Milk froth
- Press the power button first. Then, press the steam button. The steam indicator light will
light up steady once the preheating process is complete.
- Pour milk into the container to be used for frothing. Fill 1/3 of it.
- Recommendation: It is recommended to use cold whole milk for optimal results.
- Release some steam before using it to froth milk. Once the tube has produced some steam,
switch off the function, insert the steamer 1 cm into the milk and slowly turn the steam
knob counterclockwise until steam is released.
Fig. 5.
1. Switch-off
2. Steam/water
Note:
The steamer may drip a little before producing steam.
When milk temperature starts to rise (to up to 75 ºC) and milk froth volume starts increasing,
turn the steam knob clockwise to the Off position and press the steam button to stop the
steam function.
Warning:
Clean the steam outlet with a wet sponge immediately after use. Then, remove the steamer
and clean the inner duct. It is also recommended to emit steam again to clean possible milk
remaining inside the tube.
Hot water
- Turn the steam knob to the water position. The steamer will start dispensing hot water.
- Turn the steam knob back to the Off position to disable this function.
Memory function
- Once the coffee machine has preheated and the 1-coffee and 2-coffee indicator lights light
up steady, hold down the 1-coffee button. The coffee machine will start brewing coffee.
- Once the desired amount of coffee has been obtained, stop pressing the 1-coffee button.
The machine will emit a sound, indicating it has saved the quantity.
- The coffee machine brews coffee 60 seconds approx. by default, which is the maximum
time coffee can be brewed and saved.
Note:
The setting will not be registered and saved unless the button is pressed for long enough.
- If you want to prepare a larger espresso or 2 espressos, follow the steps above and use the
CAFELIZZIA 790 STEEL PRO/SHINY PRO/WHITE PRO/BLACK PRO
ENGLISH
37