höfats SPIN 900 Instrucciones De Uso página 19

HANGING THE SPIN AS A HANGING FIRE
FIGURE L, M, N, O
Either you have already purchased the SPIN as a SPIN hanging fire
or you can convert your SPIN to a SPIN hanging fire with the hanger.
Legend:
1. Extinguishing cover
2. Glass cylinder
3. Body
4. Stainless steel cable with hook and clamp element
5. Hanger
6. Mounting material (eye bolt 6X45, expansion dowel)
7. Allen key for clamping element
8. Eco-Ring
9. Bio-Burner
• Use the the SPIN body for the conversion without the base and
without additional riser.
NOTICE
The SPIN should be hung in a cantilevered
manner from a ceiling or truss. It may only
be installed on solid concrete ceilings or
solid wood, as this is the only way to ensure
that the eye bolt is sufficiently strong.
Installing on concrete
• For secure attachment to concrete, a pre-drilled hole with Ø 10
x 60 mm must be made at the intended location.
• For secure attachment, use the eye bolt with dowel included in
the scope of delivery.
• The screw must withstand a tensile force of at least 60 kg.
Consult an appropriate specialist for the installation.
Installing on wood
• For secure attachment on solid wood, a pre-drilled hole with Ø
4 x 60 mm must be made at the intended location.
• Use the eye bolt included in the scope of delivery for secure
attachment.
How to install the SPIN as a hanging fire
• Screw the body into the thread of the hanger (Figure N1).
• Connect the hook on the loop of the stainless steel cable to the
hanger.
• Adjust your SPIN hanging fire to the desired height with the
help of the infinitely adjustable stainless steel cable (Figure O).
To do this, open the Allen screw on the clamping element.
• When tightening the screw again, ensure that there is sufficient
clamping force. The easiest way to check this is by pulling the
lower end of the frame.
• Make sure that the stainless steel cable is not kinked;
otherwise permanent deformation may occur.
• Insert the Bio-Burner into the body (Figure N2).
• Place the glass cylinder on the body (Figure N3).
• Follow the instructions under "Lighting the fire".
NOTICE
Adjusting the height of the SPIN hanging
fire and hanging it must always be done
without the glass cylinder.
• Only hang the SPIN hanging fire in places
sheltered from the wind to prevent
uncontrolled swinging of the SPIN.
• If the SPIN hanging fire begins to swing, it
must be brought back to its resting position
as quickly as possible. Always use heat-
resistant gloves to avoid burns.
SETTING UP THE SPIN WITH THE RISER
FIGURE P
You can use SPIN with a riser. The SPIN can be elevated from the
ground using the riser.
• Screw the riser between the base and the body of the SPIN.
• Insert the Bio-Burner into the body.
• Place the glass cylinder on the body.
• Follow the instructions under "Lighting the fire".
WARNING!
The SPIN must not be used indoors when
set up using the SPIN riser!
Never use more than one riser with the
SPIN!
FILL BIO BURNER FIGURE A
NOTICE
The use of fuels other than those
recommended in the technical data can
lead to unwanted soot formation and less
flame formation or excessively high flames.
In addition, the Bio-Burner can be
destroyed.
Only fill the Bio-Burner with liquid fuels
from höfats. This is the only way to ensure
that it operates properly.
• Before filling with liquid fuel, check the Bio-Burner for dirt or
damage.
• Insert the Bio-Burner into the body of the SPIN (Figure A1).
• Fill the Bio-Burner with the liquid fuel suitable for your Bio-Burner
up to the "max" mark (Figure A2).
LIGHTING THE FIRE FIGURE B
Optional: Use Bio-Burner with Eco-Ring
(Figure B1)
• If you put the Eco-Ring on the Bio-Burner after filling, the flame
is reduced a little and you save liquid fuel! This also means your
SPIN will burn for longer.
– Risk of burns from hot
CAUTION!
surfaces! Only touch the Eco-Ring when
it has cooled down and not directly after a
burning process.
• Light the Bio-Burner at the mesh with a stick lighter
(Figure B2).
EN