Publicidad
Idiomas disponibles
Idiomas disponibles
Safety
"READ ALL INSTRUCTIONS"-- Failure to follow the SAFETYRULES identified by BULLET (e) symbol
listed BELOWand other safety precautions, may result in serious personal injury.
General Safety Rules
for Bench Top Tools
Work Area
Keep work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate
power tools
in explosive
atmospheres,
such as in the presence
of
flammable
liquids,
gases
or dust.
Power
tools create sparks which may ignite the dust or
fumes.
•
Keep bystanders, children and visitors away
while
operating
a power
tool.
Distractions
can cause you to lose control.
•
Store idle tools out of reach of children
and
other
untrained
persons.
Tools are danger-
ous in the hands of untrained users.
•
Do not leave tool running
unattended,
turn
power off. Do not leave tool until it comes to a
complete stop.
•
MAKE
WORKSHOP
CHILDPROOF
with pad
lock, master switches, or by removing starter
keys.
Electrical
Safety
Before plugging in the tool, be certain the
outlet voltage
supplied is compatible
with
the voltage marked on the nameplate within
10%. An outlet voltage incompatible
with that
specified on the nameplate can result in serious
hazards and damage to the tool.
Double insulated tools are equipped with a
polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does
not fit,
contact
a qualified
electrician
to
install a polarized outlet. Do not change the
plug in any way. Double insulation eliminates
the need for the three wire grounded power cord
and grounded power supply.
Avoid body contact with grounded surfaces
such as pipes, radiators,
ranges and refrig-
erators.
There is an increased risk of electric
shock if your body is grounded.
Do not expose power tools to rain or wet
conditions.
Water entering
a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Replace damaged
cords
immediately.
Damaged cords increase
the risk of electric shock.
When operating a power tool outside, use an
outdoor extension
cord marked
"W-A"
or
"W". These cords are rated for outdoor use and
reduce the risk of electric shock.
Personal
Safety
Stay alert, watch what you are doing and use
common
sense
when
operating
a power
tool. A moment of inattention or use of drugs,
alcohol or medication
while operating
power
tools can be dangerous.
Dress properly.
Do not wear loose clothing
or jewelry.
Contain
long
hair.
Keep your
hair, clothing
and gloves away from moving
parts. Loose clothes, jewelry or long hair can be
caught
in moving
parts.
Roll long sleeves
above
elbows.
Rubber
gloves and non-skid
footwear are recommended when working out-
doors.
Avoid accidental starting. Be sure switch is
"OFF" before plugging in. Carrying tools with
your finger on the switch or plugging in tools
that have the switch "ON" invites accidents.
Remove adjusting keys or wrenches
before
turning the tool "ON". A wrench or a key that
is left attached to a rotating part of the tool will
be thrown.
Do not overreach,
keep proper footing
and
balance at all times. Proper footing and bal-
ance enables better control of the tool in unex-
pected situations.
Do not stand on tool or its stand. Serious
injury may occur if the tool is tipped or if the cut-
ting tool is accidentally contacted. Do not store
materials on or near the tool such that it is nec-
essary to stand on the tool or its stand to reach
them.
"SAVE
THESE
INSTRUCTIONS"
2.
Publicidad
