Teka DV-80 Manual De Instrucciones página 13

_lmanual_dv_cr_260ump.QXp 18/02/2008 11:26
p~
+
,
with the long bolts (D) (04 x 30).
11) Fit the part (B) il the inner tube (not
supplied) is 0120.
12) Attach the inner tube with a clamp (not
supplied) to (B) or on to the motor's air outlet
vent
as the case
may be.
13) Once the inner tube is fitted, fit the lower
tubecover around
the extractor
fan outlet and
attach the upper tubecover with the screws (G)
(03,9 x 20).
~
Active ch~l'filler,s_(QpJional).'"
When exterior gas extraction is not possible,
then the kitchen hood may be set to purily the
--:-1
air by recycling it through aetive charcoal
filters.
Fig. 1 (Page 31)
The active charcoal filters have an active lile 01
On installingthe kitchen hood
make sure between three
to six months, depending on
that the Salety Instructions set out on page the individual conditions 01 use. These filters
10 are complied with. cannot be washed nor regenerated. They must
To obtain optimum performance, the external be replaced
once
their useful
life comes to an
conduct must not be more than FOUR end.
METRES long, have no more than two 900 Fig. 2 (page 31)
angles and its diameter must be at least 0120. 1) Trace and drill the points lor fitting the wall
1) Trace and drill the points lor fitting the wall plugs onto the wall (P) (08 x 40) and (J) (06 x
plugs onto the wall (P) (08 x 40) and (J) (06 x 30).
~
30). 2) Attach the Supports (O) to the wall using the W
2) Attach the Supports (O) to the wall using the long bolts (Q) (05 x 45) and the support (H)
long bolts (Q) (05 x 45) and the support (H) with the long bolts (1)(04 x 30), as in figure 1.
with the long bolts (1) (04 x 30), as in figure 1. 3) Hang the kitchen hood onto the mounted
3) Hang the kitchen hood onto the mounted supports (O). Straighten the appliance by
supports (O). Straighten the appliance by tightening the long bolts (L) (M4 x 12).
tightening the long bolts (L) (M4 x 12). 4) Open the lateral doors. Remove the metal
4) Open the lateral doors. Remove the metal filters.
lilters. 5) Drill into the wall and fit the wall plugs (R)
5) Drill into the wall and fit the wall plugs (R) (08 x 40), through the inside 01 the kitchen
(08 x 40), through the inside 01 the kitchen hood.
hood. 6) Tighten the screws (M) (M4 x 12) with the
6) Tighten the screws (M) (M4 x 12) with the washers (A3) (06,4 x 012) and the long bolts
washers (A3) (06,4 x 012) and the long bolts (S) (05 x 45) with the washers (T) (06,4 x
(S) (05 x 45) with the washers (T) (06,4 x 018).
018). 7) Put the filters into the lateral draught seetion
7) Fit the metal filters. Close the lateral door.
01 the motor making the holes in the filters
8) Mount the tubecovers, attaching the lower match up (A11) with the pivots (A 12) 01 the
one to the support (H) as per the detail in figure motor carcass. Turn as indicated
in the
1. Lift the upper tubecover up to the desired diagram.
height and mark its shape on the wall. Remove 8) Fit the metal filters. Close the lateral door.
the tubecovers. II the kit is not ¡ncluded in the cooker hood:
9) Fit the clips (F) to the support (C).
Fit the diffuser (A5) on to the motor's air outlet
10) Centre the support (C) around the shape vent with the screws (A4).
marked; trace and drill the fixing points lor the Send the tubecovers
to an authorized
wall plugs (E) (06 x 30). Attach the support (C) recycling area,
1
2
2
6
6
4
4
2
2
2
4
2
150/120 mm reduction.
Support lor tubecover.
Wall support.
Wall plugs (08 x 40).
Long bolts (05 x 45).
Wall plugs (06 x 30).
Long bolts (04 x 30).
06,4 x 018, washers.
06,4 x 012, washers.
Screws (03,9 x 20).
Screws (04 x 12).
Clips.
-fnst3f1ation
13
-+-
L
+
I