Publicidad
Idiomas disponibles
Idiomas disponibles
TRANSAXLE
MOTION CONTROL LEVER
NEUTRAL
ADJUSTMENT
The
motion
control
lever
has been
preset
at the
factory
and
adjustment
should
not
be necessary.
1.
Loosen
adjustment
bolt
in front
of the
right rear wheel,
and lightly tighten.
2.
Start
engine
and
move
motion
control
lever until tractor
does not move forward
or backward.
3.
Hold motion
control
lever in that position
and turn engine
off.
4.
While
holding
motion
control
lever
in
place,
loosen
the adjustment
bolt.
5.
Move motion
control
lever to the neutral
(lock gate)
position.
6.
Tighten
adjustment
bolt securely.
NOTE:
If additional
clearance
is needed
to
get to adjustment
bolt, move
mower
deck
height
to the lowest
position.
After above
adjustment
is made,
if the trac-
tor still creeps
forward
or backward
while
motion
control
lever
is in neutral
position,
follow
these
steps:
1.
Loosen
the adjustment
bolt.
2.
Move the motion
control
lever
1/4 to 1/2
inch in the direction
it is trying
to creep.
3.
Tighten
adjustment
bolt securely.
4.
Start engine
and test.
5.
If tractor
still creeps,
repeat
above
steps
until satisfied.
Motion Control
Lever
Adjustment
Bolt
tral
Lock Gate
FRONT
WHEEL
TOE-IN/CAMBER
Your new tractor
front wheel toe-in
and cam-
ber is set at the factory
and is normal.
The
front wheel toe-in and camber
are not adjust-
able.
If damage
has occurred
to affect
the
factory
set front wheel toe-in or cam ber, con-
tact a Sears or other qualified
service
center.
TO REMOVE WHEEL FOR REPAIRS
1.
Block
up axle securely.
2.
Remove
axle
cover,
retaining
ring and
washers
to allow
wheel
removal
(rear
wheels
have a square
key - Do not lose).
3.
Repair
tire and reassemble.
NOTE:
On rear wheels
only: align grooves
in
rear wheel
hub and axle. Insert square
key.
4.
Replace
washers
and snap retaining
ring
securely
in axle groove.
5.
Replace
axle cover.
NOTE:
To seal tire punctures
and prevent
flat tires
due to slow
leaks,
purchase
and
use tire sealant
from Sears. Tire sealant
also
prevents
tire dry rot and corrosion.
Washers
Retaining
Axle
Cover
Square
TO START ENGIN E WITH WEAK
BATTERY
_,WARNING:
Lead-acid
batteries
generate
explosive
gases.
Keep
sparks,
flame
and
sm oking materials awayfrom
batteries. Always
wear eye protection
when
around
batteries.
If your battery is too weak to start the engine,
it
should
be recharged.
(See "BATTERY"
in the
MAINTENANCE
section
of this manual).
If "jumper
cables"
are used for emergency
starting,
follow
this procedure:
IMPORTANT:
Your tractor
is equipped
with a
12 volt system.
The other vehicle
must also
be a 12 volt system.
Do not use your tractor
battery
to start other vehicles.
TO ATTACH JUMPER
CABLES -
1.
Connect
one end ofthe
RED cable to the
POSITIVE
(+) terminal
of each battery(A-
B), taking care not to short against
tractor
chassis.
2.
Connect
one end of the
BLACK
cable
to the NEGATIVE
(-) terminal
(C) of fully
charged
battery.
3.
Connect
the
other
end
of the
BLACK
cable
(D) to good chassis
ground,
away
from fuel tank and battery.
24
D
Weak or Dead
Fully Charged
Battery
Battery
Publicidad
