Publicidad
Idiomas disponibles
Idiomas disponibles
Instructions for installation and use
ROLLER BLIND Radio-controlled 12 V motor
3.1 Pair motor and first remote control unit
DE
done at the factory)
The time between two entries must not be longer than 6 seconds.
i
Otherwise the entries get deleted. The entries then have to be repeated.
1. With hand-held remote control units pull off the back cover to make the setting.
Caution: Keep battery gently pressed down (contact).
After making the setting, push the cover back on.
When pairing a multi-channel remote control unit,
i
before moving to the next step use the P1 buttons
on the RC unit to switch to the channel to be
assigned for this drive system.
2. Hold down setting button on
the motor for c. 3 seconds.
=> Roller blind confirms with
1 beep
+ short movement.
FR
3. On the remote control unit press the P2 button once
=> Roller blind confirms with 1 beep + short movement.
4. On the remote control unit press the P2 button once
=> Roller blind confirms with 1x beep.
5. If: - Motor on right / Blind at back, - Motor on left / Blind at front
Then: Press the UP button on the radio transmitter once
If: - Motor on right / Blind at front, - Motor on left / Blind at back
Then: Press the DOWN button on the radio transmitter once
=> Roller blind confirms with 6 beep + short movement.
FL
3.2 Setting the top/bottom end position
(generally already been done at the factory)
i
In order to change the end positions, they must first either have been deleted as
at 3.6 or changed as described at 2.2.
1. With hand-held remote control units pull off the back cover to make the setting.
Caution: Keep battery gently pressed down (contact).
After making the setting, push the cover back on.
2. On the remote control unit press the P2 button once
=> Roller blind confirms with 1 beep + short movement.
3. On the remote control unit press the UP button once
=> Roller blind confirms with 1 beep + short movement.
4. On the remote control unit press the P2 button once
EN
=> Roller blind confirms with 4 beeps + short movement.
5. On the remote control unit press the UP button once
Option: Gradually move towards end positions: As a set-
ting aid this additional function can be used if necessary.
During the travel UP process, press the P2 button on the
remote control unit once => Roller blind moves gradually.
6. On the remote control unit, press the STOP button once
as soon as the desired top end position has been reached.
7. Press the STOP button on the remote control unit 5 times
=> Roller blind confirms the programming of the top end
position with a beep when the button is pressed +short
movement.
8. On the remote control unit press the DOWN button once
Option: Gradually move towards end positions: As a set-
ES
ting aid this additional function can be used if necessary.
During the travel DOWN process, press the P2 button
on the remote control unit once => Roller blind moves
gradually.
9. On the remote control unit, press the STOP button once as
soon as the desired bottom end position has been reached.
10. Press the STOP button on the remote control unit 5 times
=> Roller blind confirms the programming of the bottom
end position with a beep when the button is pressed +
short movement.
16 16
IT
(generally already been
DOWN button
P1 button +
P1 button –
Charging socket
Setting button
P2
P2
P2
P2
STOP
STOP
3.3 Change rotary direction of the drive system with end positions set
i
To change the rotary direction again, repeat point 1.
1. Keep setting button on drive unit pressed for 3 short
movements, each c. 4 seconds apart.
=> Roller blind confirms with 3 short movements about
4 seconds apart + 3 beeps after release of the setting
button.
3.4 Set pin-point operating mode (option)
1. With hand-held remote control units pull off the back cover to make the setting.
Caution: Keep battery gently pressed down (contact).
After making the setting, push the cover back on.
2. On the remote control unit press the P2 button once
=> Roller blind confirms with 1 beep + short movement.
3. On the remote control unit press the UP button once
=> Roller blind confirms with 1 beep + short movement.
4. On the remote control unit press the DOWN button once
=> Roller blind confirms with 2 beeps + short movement.
Pin-point operation through brief pressing of the UP/DOWN button.
i
Press the UP/DOWN button for a prolonged time for smooth movement.
To delete the setting, repeat steps 2 to 4.
3.5 Programming a third blind position (option)
It is possible to assign an additional stop position to the roller blind.
i
This position can only be between the two end positions.
1. With hand-held remote control units pull off the back cover to make the setting.
Caution: Keep battery gently pressed down (contact).
After making the setting, push the cover back on.
2. Using the UP or DOWN button, move the roller blind into
the desired position.
Press the STOP button
3. On the remote control unit press the P2 button once
=> Roller blind confirms with 1 beep + short movement.
4. On the remote control unit press the STOP button once
=> Roller blind confirms with 1 beep + short movement.
5. On the remote control unit press the STOP button once
=> Roller blind confirms with 3 beeps + short movement.
Press the STOP button for 3 seconds. The blind moves into the third blind
i
position. If pin-point mode has been set, the blind first moves to the bottom end
position and then into the third blind position. To delete the third blind position,
repeat points 3 to 5.
Subject to technical changes I
P2
STOP
P2
Edition 09.2019
Publicidad
