Milwaukee 8988-20 Manual Del Operador página 3

IMPORTANT SAFETY
INSTRUCTIONS HEAT GUNS
Read These Instructions
• Danger when opening up the tool,
DANGER
as live parts are exposed. Before
opening, unplug the tool to ensure disconnec-
tion from the mains. Before putting into opera-
tion, check power supply cord and connector
as well as extension cable for electrical and
mechanical damage.
• Incorrect use of the Hot Air Tool (eg. overheating
of the material) can cause a fire and explosion
hazard, especially near combustible materials
and explosive gases. Do not apply to the same
place for a long time. Heat can ignite flammable
materials which are not in view.
• Fire and burn hazard! Do not touch the heating
element housing and air nozzle when they are
hot as they can cause burns. Let the tool cool
down. Do not point the hot air flow in the direc-
tion of people or animals. Before replacing a
nozzle or storage after use, place the tool vertical
down on its standing surface and allow it to cool
down completely. If the Hot Air Tool switches
off autonomously in operation (thermal relay),
switch tool off or disconnect the power supply
from mains. Before reusing, let the tool cool
down.
• The voltage rating stated on the
CAUTION
tool must correspond to the mains
voltage.
• For personal protection on building sites we
strongly recommend the tool be connected to
a RCCB (Residual Current Circuit Breaker).
• The tool must be operated under supervision.
This tool may be used by children aged 8 or
above and by persons with reduced physical,
sensory or mental capabilities or lack of experi-
ence and knowledge if they are supervised or
have been given instructions on how to use the
tool safely and understand the hazards involved.
Do not allow children to play with the tool.
Children are not allowed to clean or carry out
maintenance work on the tool without supervi-
sion.
• Protect tool from damp and wet.
• Repairs should only be carried out by authorized
service points. Restricted to use with original
accessories and spare parts.
• This appliance has a polarized plug (one blade
is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
Do not modify the plug in any way.
• Know your work environment. Hidden areas such
as behind walls, ceilings, floors, soffit boards and
other panels may contain flammable materials that
may ignite when using the heat gun in these loca-
tions. Ignition of these materials may not be readily
apparent and could result in property damage and
personal injury. Check these areas before applying
heat. If in doubt, use an alternate method. Pausing
or lingering in one spot may ignite the panel or the
material behind it. Keep heat gun moving to avoid
excessive temperatures.
• Do not direct the heat gun air flow at clothing,
hair or other body parts. Do not use as a hair
dryer. Heat guns can produce 1200°F (650°C) or
more of flameless heat at the nozzle. Contact with
the air stream could result in personal injury.
• Do not use near flammable liquids or in explo-
sive atmospheres, such as in the presence of
fumes, gases or dust. The flameless heat from
the heat gun may ignite the dust or fumes. Remove
materials or debris that may become ignited from
work area.
• Shield materials around the heated area to pre-
vent property damage or fire.
• Keep a fire extinguisher nearby. Heat guns may
ignite flammable materials left in the work area.
•
Hot Surfaces. Always hold the heat
WARNING
gun by the plastic enclosure. Do
not touch nozzle, accessory tips or store heat
gun until the nozzle has cooled to room tem-
perature. The metal nozzle requires approximately
20 minutes to cool before it can be touched. Contact
with the nozzle or accessory tip could result in per-
sonal injury. Place the heat gun in a clear area away
from combustible materials while cooling to prevent
flammable materials from igniting.
• Do not cut off air flow by placing nozzle too close
to workpiece. Keep intake vents clean and clear
of obstructions. Restricting air flow may cause the
heat gun to overheat.
• Place the heat gun on a stable, level surface
when not hand held. Use the support pads or
support stand. Place cord in a position that won't
cause the heat gun to tip over.
• Do not leave the heat gun unattended while run-
ning or cooling down. Inattention invites accidents.
• Store indoors in a dry location. Do not expose to
rain or moisture.
• Do not direct air flow directly on glass. The glass
may crack and could result in property damage or
personal injury.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
3