ENGLISH
Milk froth
-
With the machine switched on and preheated, press the steam button. The steam indicator
light will flash and then remain steady when the preheating process is complete.
Pour milk into the container where you want to froth milk. Fill up 1/3 of the container.
-
-
Recommendation: it is recommended to use cold whole milk for optimal results.
-
Place an empty glass under the frother, turn the steam knob to the steam/water position,
and let the tube emit steam before frothing the milk. Once steam is emitted, deactivate the
steam function by returning the steam knob to the off position, insert the 1-cm steam tube
into the milk, and turn the steam knob slowly counterclockwise until steam is produced.
Fig. 5
Fig. 5
1.
Power Off
2.
Steam/water
Note
The vaporiser may emit a few drops of water before producing steam.
When milk temperature starts to rise (to up to 75 ºC) and milk froth volume starts increasing,
turn the steam knob clockwise to the 0 position and press the steam button to stop the steam
function.
Warning
Clean the steam outlet with a wet sponge immediately after use. Then, remove the steam tube
and clean the duct interior part. Moreover, it is advisable to emit steam into an empty glass to
get rid of any traces of milk left.
Hot water
-
With the coffee machine switched on and preheated, turn the steam knob to the steam/
water position. The steam tube will start dispensing hot water.
-
Turn the steam knob back to the 0 position to deactivate this function.
Memory function
-
Once the coffee machine has preheated and 1-coffee and 2-coffee light indicators remain
steady, hold down the 1 espresso button. The machine will start brewing coffee.
When you have obtained the desired amount of coffee, stop pressing the espresso button.
-
The machine will emit a sound, indicating it has saved the quantity.
-
The coffee machine brews coffee 60 seconds approx. by default, which is the maximum
time coffee can be brewed and saved.
38
CAFELIZZIA 790 BLACK
Note
The setting will not be registered and saved unless the button is pressed for long enough.
If you want to prepare a larger espresso or 2 espressos, follow the steps above and use the
2-coffee button instead of the 1-coffee one.
Factory settings
If you want to restore factory settings, hold pressed the 1-coffee button and the steam button
for 3 seconds. The device will beep once, indicating factory settings have been successfully
restored.
Device cooling process
-
After steam is emitted or coffee is brewed, the device's temperature is likely to increase
significantly, which means that all its components will become very hot as the device has
been operating at high pressure. Both light indicators, 1 and 2 coffees, will start blinking
quickly, indicating the device's temperature must be decreased.
-
To cool down the device:
1.
Rotate the steam knob to the water position, the machine will start dispensing water for
a few seconds.
2.
When the indicator lights start flashing slowly, turn the steam knob to the 0 position.
3.
When the power light indicators remain steady on, the device is ready to use again.
Please note
The coffee machine features an auto-off safety system that activates after 25 minutes the
machine is not being used.
4. CLEANING AND MAINTENANCE
-
Disconnect the device from the power supply and allow it to cool down completely before
cleaning.
-
Do not use abrasive cleaners or scouring pads as they could cause damage to the product's
surface.
-
Use a soft, dampened cloth to clean the outer part of the device.
Do not immerse the main body in water or other liquids.
-
-
Wash the water tank, drip tray, and cup holder tray regularly.
-
After using the steam function, the tube must be cleaned with a cloth immediately after.
Be careful not to burn yourself! Allow steam to be released to avoid possible blockages
inside the tube.
-
If the steam tube is clogged, use a needle to unblock the conduct.
-
Remove the coffee machine arm after each use and empty the coffee residues inside. Then,
ENGLISH
CAFELIZZIA 790 BLACK
39