Chicco LIVING Instrucciones De Uso página 14

3 – To remove the hood, first extract the 4 tabs from the rear arch (dia-
gram 3A) and then remove the front arch by pressing the two round
buttons on the supports of the connection base (diagram 3B).
WARNING: Incorrect removal of the hood can break the tabs.
SUN VISOR
4 – Inside the hood, between the visor and the first section, there is a fabric
ring from which you can hang soft toys, with convenient hooks (figure 4).
WARNING – use only Chicco toys with the following code numbers:
60062, 60063, 60065.
REAR OPENING
5 – To ensure maximum ventilation, the canopy has an adjustable rear
opening. To adjust the opening, open the zip (diagram 5A) and fold the
fabric panel onto the upper part of the canopy (diagram 5 B).
INTERNAL LINING AND COVER
6 – To fit the internal lining inside the carrycot: slide the plastic strip po-
sitioned where the baby's head will lie between the polystyrene support
and the carrycot body; then connect the two "tabs" where the baby's
feet will lie and the side ones under the body rim, as seen in diagram 6A.
Fasten the fabric in place in the centre of where the baby's feet will lie,
inserting the eyelet over the relative hook (diagram 6B) and then close
the two side snap-buttons (diagram 6C). The cover is then fitted using
the zip (diagram 6D) and by fastening the side clips of the fabric to the
hood (diagram 6E).
Once it has been fitted, it can be opened from both sides (diagram 6F).
ADJUSTABLE BACKREST - COMFORT SYSTEM
7 – The backrest of the carrycot can be adjusted gradually. To raise or
lower the backrest, operate the external rear wheel of the carrycot, lo-
cated near the end of the carrycot (diagram 7).
WARNING: It is recommended to air the carry cot when it has been
used for a long time.
CARRY HANDLE
8 - The carrycot has a practical carry handle that can be adjusted to
three positions (diag. 8):
A) Carrying position
B) Intermediate position
C) Rest position
9 – To position the handle vertically, hold it in a central position and
pull it in an upward direction, until a clack is heard, indicating that it is
correctly locked into position (diagram 9a). To replace the handle in the
rest position, press the two buttons located on the base of the handle at
the same time, and then turn it in a downward direction (diagram 9b).
WARNING: The carry cot must never be carried with the handle in the
intermediate or rest position; it can only be carried with the handle in
the transportation position.
WASHING
The hood, the internal lining of the carrycot and the mattress are all re-
movable and washable; please follow the washing instructions indicated
on the labels carefully.
10 – Remove the carrycot hood following the instructions in section 3;
undo the buttons on the fabric (diagram 10A) then remove the metal
arch only, by pulling one end (diagram 10B); do not remove the rear arch
with the 4 tabs when washing.
11 - Remove the padding from the mattress from the opening on the
back of the lining (diagram 11).
12 – To remove the internal lining from the carrycot, undo the side but-
tons (diagram 12A), slide the eyelet from the hook (diagram 12B) re-
move the plastic strip from the area where the baby's head will lie, the
"tabs" in the area where the baby's feet will lie and the side ones from
the body rim (diagram 12C)
HOW TO USE THE CARRYCOT AS A PRAM
This carrycot can be fitted onto the Chicco strollers featuring the "Clik
Clak" system and used as a pram.
HOW TO FIT THE CARRYCOT TO THE STROLLER
To fit the carrycot to the stroller, position the stroller, fitted with the Clik
Clak system, as shown in the instructions of the stroller.
NB: If the stroller has a removable backrest or seat, it is recommended
to remove the backrest or seat as indicated in the instructions of the
stroller.
13 - Hold the handle in the carrying position and place the carrycot onto
the armrests, with the footrest end of the carrycot facing the handle of
the stroller (diagram 13).
14 - Ensure that the two joints, located on the two sides of the carry-
cot, coincide with the openings located on the armrests of the stroller
(diagram 14 A); then position the carrycot. A clack will indicate that it is
locked correctly into place (diagram 14 B).
WARNING: Pull the carry cot upwards to check it is firmly fastened in
place before using it.
HOW TO REMOVE THE CARRYCOT
15 - Position the handle in a vertical position (carrying position) until a
clack is heard, indicating it is locked into position (diagram 15).
16 - Press the grey button located in the front part of the pram (diagram
16 A); then, while keeping the button pressed, lift the carrycot from the
frame (diagram 16 b).
WARNING: The carry cot can be fastened and unfastened with the baby
inside; these procedures could prove more difficult due to the weight of
the baby. Be very careful when performing the above indicated proce-
dures.
WARNING: The incorrect fitting of the carrycot to the frame (e.g.: fitting
the carrycot on the wrong side) can damage the locking system, making
the removal of the carrycot impossible. Should this happen, please refer
to the instructions of the stroller or contact Artsana Customers Service.
Below are the cleaning symbols and their meanings:
Wash by hand in cold water
Do not bleach
30° C
Do not tumble dry
Do not iron
Do not dry clean
FOR UK MARKET ONLY: COMPLY TO BS
7409
• WARNING: When used as a pram body, re-
member that the depth from the top of the
mattress to the top of the side of a body at, or
at any position within 300 mm from, the har-
ness attachment points, should not be reduced
to less than 140 mm when the mattress is in
position and that mattresses purchased sepa-
rately should conform to BS 1877 : Part 10.
• SAFETY HARNESS – For extra safety if required, "D" rings are provided
for the attachment of a separate safety harness approved to BS6684.
The rings are positioned inside the carrycot on the left and right sides
as shown in fig. 17.
WARNING: when using this product in the car, use the lap belt assem-
bled on the carrycot frame only.
14
AV
IM
TA
NE
VA
NO
HI
CI
CU
M
LO
LA
FU
AD
•
•
•
•
•
•
•
•