Sleepnet IQ2 Manual Del Usuario página 6

Dispose of the mask and accessories in accordance with local and regional guidelines.
 This mask has a non-transferable three-month limited warranty for manufacturer's defects from the date
of purchase by the initial consumer (or maximum service life, if shorter). If a mask used under normal
conditions should fail, Sleepnet will replace the mask. For additional information about the Sleepnet
Warranty, please visit http://www.sleepnetmasks.com/.
NOTE: The mask cushion has a service life of the 1 month. The swivel frame/tube set has a service life
of 3 months. The TruFit Headgear and magnetic clips have a service life of 6 months.
Cleaning is recommended on a daily basis. Refer to disassembly instructions. Wash the mask and components
in warm water using a mild soap such as Ivory
the vent holes are clear and allow the mask to air dry. Washing your face prior to fitting the mask will remove
excess facial oils and help extend the life of the mask.
NOTE: The gel cushion, although silky to touch, will not tear, leak, or detach from the mask under normal
use and following recommended cleaning and maintenance protocols. However, the gel cushion is not
indestructible. It will tear, cut, and rip if subjected to mishandling or abuse. Do not clean in a dishwashing
machine. The warranty does not cover these types of product failures. Therefore, please handle your new iQ
Nasal Vented Mask with care.
WARNING: Frequency of cleaning, methods of cleaning or the use of cleaning agents, other than those
specified above, or exceeding the service life of the components can have an adverse effect on the device and
consequently the safety or the quality of the therapy.
Therapy pressure range: 3 to 30 cm H
Resistance to air flow at 50 L/min: 0.45 cm H
Resistance to air flow at 100 L/min: 2.05 cm H
DEAD SPACE VOLUME (mL approx.): Mask – 47.3ml Tube – 68.3ml
Operating Temperature: Do not expose the mask to temperatures above 122˚F (50˚C).
 Inspect mask daily or prior to each use. Replace the mask if vent holes are blocked, if parts are damaged,
or if gel is exposed due to tears or punctures.
1. Take mask out of the bag. Adjust the base strap according to your general size by aligning the tab at the
indicated size markings (S, M, L, XL). (Figure 1).
2. Detach one magnetic clip from the mask. (Figure 2).
3. After placing the mask on your head, reattach the magnetic clip. (Figure 3).
4. First, adjust the top strap to raise or lower the mask. (Figure 4).
5. Second, adjust the left/right straps to make sure the bottom of the mask is sealed comfortably between the
bridge of the nose and just above the upper lip. (Figure 5).
6. Connect the mask to the possible airway pressure device tubing and turn the device on to the prescribed
pressure. Turn head from side to side while lying on the bed to assure secure fit. (Figure 6).
7. If unacceptable leaks occur, try moving the mask higher or lower around the nose to find the best fit. (Figure 7).
8. Gently press edges of the mask to change mask shape, create a comfortable fit, and reduce leaks. (Figure 8).
9. If leaks persist, try moving the mask higher or lower around the nose to find the best fit. (Figure 9).
1. Firmly hold the mask cushion in one hand at one of the bottom corners. (Figure 1).
2. Grasp the Swivel Frame by one of the magnets. (Figure 2).
3. Firmly pull to separate the Swivel Frame from the cushion in a peeling motion. (Figure 3).
1. Hold the Swivel Frame up to the mask, slightly tilted up (Figure 1). Using your fingers, support the mask seal
ring from inside.
2. Slide the top part of the Swivel Frame into the mask until the mask posts lock into the Swivel Frame grooves
(Figure 2).
3. Softly push the bottom part of the swivel frame into the mask until the Swivel Frame tab locks into place (Figure 3).
4. Visually inspect inside the mask to ensure that the seal ring is properly seated onto the Swivel Frame (Figure 4).
iQ ® 2 is a trademark of Sleepnet Corporation.
Visit our website at www.sleepnetmasks.com.
6
GENERAL INFORMATION
CLEANING AND MAINTENANCE
. Rinse the mask thoroughly after washing. Visually verify that
®
TECHNICAL INFORMATION
O
2
O
2
O
2
BEFORE USE
IQ ® 2 FITTING INSTRUCTIONS
DISASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
2
®