Publicidad
Idiomas disponibles
Idiomas disponibles
Operating instructions
Stationary Air Compressor
for thermal protection (SeeFigure 4).
NOTE: 120 volt. 15 amp units can be
operated
on • 120 volt 15 amp circuit
under the following
conditions:
1. No ethel
electrical
appliances or
lights are connected to the same
branch circuit.
2. Voltage
supply is norma!.
3. Circuit is equipped
with a 15 amp
circuit breaker
or a 15 amp slow
blow fuse type T (For Canada use
TypeO|.
if the above conditions cannot be met
or if nuisance tripping
of the current
protection
device occurs, it may be
necessary to operate
the compressor
from a 120 volt 20 amp • rcuit. Some
models convert to 240 volt operation.
see DUAL VOLTAGE MOTOR.
GROUNDING
INSTRUCTIONS
1. This product is for use on a nominal
120 or 240 volt droJlt and has a
grounding plug thatlooks like one of
the plugs illustrated in Fig. 5. Make
sure product is connected to an outlet
having the same configuration
asthe
plug.This product must be grounded.
In the event of an eioctric short circuit.
grounding
reduces the risk of electrical
shock by providing an escape wire for
the electric cunent. This product is
equipped
with a cord having a
grounding wire with an appropriate
grounding
plug. The plug must be
plugged into an outlet that is properly
installed and grounded
in accordance
with all local codes and ordinances,
Impt_oer
use of gr_vndlng
I
_1
i/rmmdng
adorer.
G¢Oufld Pin
Gio_d P_n
Grinded
Grounded
Outfit
Out_t
Flgu_ s
Line
Motor
LI- °2"_V ....
Pr_sure
Switch
Figure 4 - Wiring
Diagrams
Fused Breaker
_
C_
Or Oisconned
F _*-
-d
- __(/
,', ........
_
i L3
_
..4..
Pressure
_
l_ermal
Switch
Units(3)
6T3
_111t
I_hal41t
J
wHh
Magnetic
,
MotO¢
Stlwttr
',
,"
2. If repair or replacement
of the cord
or plug is necessary, do not connect
the grounding
wire to either flat
blade terminal.
The wire with
insulation
having an outer surface
that is green with or without
yellow
stripes is the grounding
wire.
3. Check with a qualified electrician or
serviceman if the grounding instructions
are not
coml_etely
understood, of if in
doubt as to whether the product is
properly g rounded.
Do not moddy the
plug provided:
if It will not fit the outJet,
have the proper outJet imtalled by a
qualified electri_n.
PLUGS AND RECEPTACLES
1. If the plug on the electrica! cord of
the unit is unfamiliar
to you or will
not fit your particular
receptacle,
Figure 5 will help you understand
why by illustrating
the different
plugs and the voltages they are to
be used with.
2. Make sure that the product is
connected to an outlet having
the
same configuration
•s the plug.
3. The receptacles
must be connected
to circuits rated to carry at least the
voltage and amperages
shown.
4. NEVER have a receptacle
_eplaced
with one of a higher amperage
before determining
the change can
be made according
to all electrical
codes affecting
your particular
area.
The installation
should be made by
a qualified
electrician,
if the
products must he reconnected
for
use on different
types of circuits.
the re-connection
should
be made
by qualified
personnel
DUAL VOLTAGE
MOTORS
(SOME
MODELS)
The froundMg
plug
must be changed
to
convert unit for du,I
voltage.
Dual voltage motors may be connected
for either 120 volts or 240 volts. 8y
comparing
the plug on the cord with
the receptacles shown below, you can
determine
for which voltage your
compressor is factory wiRd.
Also check
motor decal to change from low
voltage to high voltage.
All wlHng must be
€omplefed
by •
quallfl_l
el_an,
Disconnect from
power sour_
before dl_.llng
any
wtrlng.
When conwrttng
to afl atten_te
volsage, be sure Che green gmund wfre
of ebe cord conneclx to the ground ptn
of/_le
p/ug and to fhe metat body of
tbe p_uure
sw/to_
ADDITIONAL
HARDWARE
NEEDED
Purchasehose, regulator and shutoff
valvethat has a minimum rating of 150
PSI and exceedsthe maximum working
pressureof the compressor.
OIL DRAIN
EXTENSION
Some models include an oil drain
extension and sap (found with the owner's
manual},
install the oil drain extend_
and
cap befo_
adding
oif to the F_attp, To
avoid oil leaks, it is highly recommended
to apply Teflon" tape o_ paste type sealant
to the threads on each end of the oil drain
Publicidad
