Additional Safety Warnings - Bosch GTS1041A Instrucciones De Funcionamiento

READ ALL INSTRUCTIONS. Failure to follow the safety rules listed below and
other basic safety precautions may result in serious personal injury.
PROTECTION:
Eyes, hands, face, ears and body.
TO AVOID BEING PULLED INTO THE SPIN-
NING TOOL, DO NOT WEAR:
• LOOSE FITTING GLOVES
• LOOSE CLOTHING
• NECKTIE, JEWELRY
DO:
• TIE BACK LONG HAIR
• ROLL LONG SLEEVES ABOVE ELBOWS
a. If any part of your saw is missing, malfunction-
ing, has been damaged or broken, such as the
motor switch, or other operating control, a safe-
ty device or the power cord cease operating
immediately until the particular part is properly
repaired or replaced.
b. The injury mitigation system requires contact
with the operator's body in order to react. This
will cause some injury to be sustained if the
contact occurs. The best defense against in-
jury remains the knowledge of how to safely
operate the saw contained within this manual
and the operator's attention to the cutting op-
eration underway.
c. Be aware of the status indicator lights. Do not
use the tool unless you understand it is safe to
use.
d. Wear safety goggles and a face shield if op-
eration is dusty. Wear ear plugs or muffs dur-
ing extended periods of operation. Small loose
pieces of wood or other objects that contact
the rear of the rotating blade can be thrown
back at the operator at excessive speed. This
can usually be avoided by keeping the guard
and riving knife in place for all "THROUGH-
CUTTING" operations (cutting entirely through
the work) AND by removing all loose pieces
from the table with a long stick of wood IMME-
DIATELY after they are cutoff.
e. Use extra caution when the guard assembly is
removed for cutting, dadoing or rabbeting —
replace the guard as soon as that operation is
completed.
f. NEVER turn the saw "ON" before clearing the
table of all tools, wood scraps, etc., except the
1600A009XC 09-15.indb 4

Additional Safety Warnings

g. NEVER place your face or body in line with the
• NEVER place your fingers and hands in the
• NEVER reach in back of the cutting tool with
• DO NOT perform any operation "FREEHAND"
• NEVER use the rip fence when crosscutting or
• NEVER hold onto or touch the "free end" of the
• Shut "OFF" the saw and disconnect the power
• Provide adequate support to the rear and sides
• Plastic and composition (like hardboard) mate-
h. If you stall or jam the saw blade in the work
SAVE THESE INSTRUCTIONS
4
work piece and related feed or support devices
for the operation planned.
cutting tool.
path of the saw blade or other cutting tool.
Keep your fingers and hands at least 4 inches
away from the blade or other cutting tool.
either hand to hold down or support the work
piece, remove wood scraps, or for any other
reason. Avoid awkward operations and hand
positions where sudden slip could cause fin-
gers or hand to move into a saw blade or other
cutting tool. Even with the injury mitigation sys-
tem engaged, these actions can lead to your
hand or arms being forced into the blade at
high speeds. A significant injury is likely under
these conditions.
— always use either the rip fence or the miter
gauge to position and guide the work.
the miter gauge when ripping. DO NOT use the
rip fence as a length stop.
work piece or a "free piece" that is cut off, while
power is "ON" and/or the saw blade is rotating.
cord when removing the table insert, chang-
ing the cutting tool, removing or replacing the
blade guard, resetting the safety system or
making adjustments.
of the saw table for wider or long work pieces.
rials may be cut on your saw. However, since
these are usually quite hard and slippery, the
anti-kickback pawls may not stop a kick back.
Therefore, be especially attentive to following
proper set-up and cutting procedures for rip-
ping. Do not stand, or permit anyone else to
stand, in line with a potential kickback.
piece, turn saw "OFF" , remove the work piece
from the saw blade, and check to see if the saw
9/14/15 1:51 PM