Descargar Imprimir esta página

cecotec Kiestra Track Manual De Instrucciones página 35

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 29
ENGLISH
Headlight bracket
3
Speedometer bracket
4
Speedometer
5
Rear fender
6
Number-plate holder swingarm
7
Tool kit
8
Rearview mirrors
9
10 Number-plate holder with built-in light
3.1. Mounting the headlight
Headlights come installed by default as shown in Figure 10.
-
To install the headlights in the correct position, first loosen the screws marked 6 and
-
remove them. Then use 4 M6 * 16 hex screws and 4 flange lock nuts to fix the headlight
bracket, and mount the headlights on the bracket as shown in Figure 10. B
Warning: some of the headlight parts have no use and must be removed. Please remove the
parts shown in Figure 11.
3.2. Mounting the swingarm for the number-plate holder with built-in light Fig. 12
To fit the number-plate holder swingarm, add a hub and replace both screws.
-
Replace the screws marked 7 and 8 with 2 M6*30 hex screws.
-
Then connect the light cable from the number-plate holder to the cable of the moped post.
-
3.3. Mounting the rearview mirrors. Fig. 13
To install the rearview mirrors, simply insert them in the handlebar holes and screw them
securely in place. Once fixed, cover the lower part with the trim piece.
3.4. Mounting the speedometer. Fig. 14-15
To install the speedometer, first mount the speedometer bracket on the handlebars. To do this,
screw 2 M6*10 hex screws into the threaded holes at the rear of the handlebar as shown in
Figure 14. Then use 2 M4*10 hex screws to fix the speedometer to the bracket.
4. OPERATION
Charging the battery. Fig. 16
WARNING: make sure the device is switched off.
Open the charging port cover (1) on the right side of the vehicle and insert the end of the
1
adapter.
Connect the other end of the power cable to a plug socket. The indicator light will turn red
2
during charging and will change to green once charge is complete.
NOTE:
68
The device comes pre-charged. However, it is recommended to charge it for 6 to 8 hours
-
before first use.
It is also recommended to charge it after every use and before storage.
-
Do not allow the vehicle to fully run out of battery to prevent damage to the latter.
-
Start-up. Fig. 17
Insert the key and turn it clockwise to start the vehicle.
Throttle and brakes. Fig. 18
The throttle and front brake are located on the right handlebar grip.
1. Turn the throttle towards you to accelerate and release to decelerate.
2. Press the brake lever on the right side of the handlebar to brake with the front wheel.
3. The rear-brake lever is located on the left side of the handlebar. Press the left brake lever
to brake with the rear wheel.
WARNING: do not turn the throttle abruptly. Turn it slowly to avoid accidents.
5. CLEANING AND MAINTENANCE
Cleaning
Clean the vehicle with a soft cloth, water, and soap if necessary.
-
After cleaning it, thoroughly dry any metal parts that may corrode or rust.
-
Grease the suspension pivot points.
-
General maintenance
Maintenance tasks must always be carried out by qualified personnel.
-
Always use original Cecotec spare parts.
-
Lower the kickstand and switch off the vehicle before carrying out any type of repair.
-
Tests to carry out
After a fall, check that the throttle grip is working properly. To do this, try accelerating and
-
decelerating several times.
Regularly check that the brakes are in proper working condition. To do this, move the
-
vehicle by pushing it manually and brake suddenly to make sure it responds.
Check that all vehicle parts are in position and securely fastened.
-
Check the screws.
-
Check wheel wear and tension.
-
Check the brakes and throttle cables for wear.
-
ENGLISH
MAKALU PRO
69

Publicidad

loading