EINHELL REDAXXO 36/25 Manual De Instrucciones Original página 23

•
Swing open the loading funnel (Fig. 11/Item
2) by opening the release screw (Fig. 11/ Item
10) and remove it. You can now remove blo-
ckages from the inside of the equipment. To
assemble, proceed in reverse order.
Important! Wear work gloves! Risk of injury
from the cutters.
6.4 Safety
The shredder has a safety switch in its interior
on the motor housing. The control unit (release
screw) for it is located on the loading funnel.
If the loading hopping is not perfectly position or
if it is not pressed against the motor housing, the
safety switch will trip and prevent the motor from
working. If this situation occurs, open the loading
funnel as described above. Carefully clean the
interior. Close the loading funnel again as descri-
bed above and ensure that when you switch on
the machine again the loading funnel is correctly
position and the safety screw is screwed right in.
IMPORTANT! NEVER undo the release screw
(Fig. 1/Item 10) without having fi rst switched off
the equipment with the On/Off switch (Fig. 1/Item
11) and having fi rst removed the battery/batteries.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Remove the rechargeable battery/batteries.
7.1 Maintenance and storage
•
Clean the machine regularly. This will help to
keep the machine in good working order and
is the basis for a long working life.
•
Keep the vent slots clean while you work.
•
Clean the plastic body and other plastic parts
with a mild household cleaning agent and
a damp cloth. Do not use any aggressive
agents or solvents for cleaning purposes.
•
Never clean the shredder by spraying with
water.
•
Prevent water getting inside the machine at
all cost.
•
Check the chassis securing screws from time
to time to ensure that they are tight.
•
If you do not intend to use the shredder for a
lengthy period, protect it from corrosion using
environmentally friendly oil.
•
Store the device in a dry room.
•
Store the device out of reach of children.
Anl_Redaxxo_36_25_SPK13.indb 23 Anl_Redaxxo_36_25_SPK13.indb 23
GB
•
When you are finished with your work, take off
the loading funnel and clean the inside. Use
a brush to remove deposits from metal parts
on the inside. Apply a thin coating of oil to the
cleaned blade plate and blades.
•
When you mount the loading funnel, make
sure that the safety switch and the release
screw are clean.
7.2 Replace, sharp and change blades
The blades on the blade plate are replaceable. If
you have to replace any blade, you must only use
genuine blades to ensure that they meet the rele-
vant quality and safety criteria.
Please note: For safety reasons we recommend
that you have all sharpening and blade replace-
ment work carried out by a specialist workshop.
Always wear heavy duty working gloves
•
Swing open the loading funnel (Fig. 11/Item
2) by opening the release screw (Fig. 11/ Item
10) and remove it.
•
Undo the blade screws (Fig. 19/Item D) using
the hex key (Fig. 3/Item 16) and remove the
blades (Fig. 19/Item E).
•
Each of the blades can be turned once as
they are ground sharp on both ends. Then
they must be replaced by new blades.
To assemble, proceed in reverse order.
•
Push the hex key (Fig. 12 / Item 16) into the
hole provided for it in the ejector housing.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Spare blade Art. No.: 34.059.31
- 23 -
25.07.2023 11:51:47 25.07.2023 11:51:47