Publicidad
Idiomas disponibles
Idiomas disponibles
ENglish
Switching On (Fig. A)
To turn the appliance on, push the lock off tab
squeeze the lock-off lever
speed trigger
1
.
To turn the appliance off, release the variable speed trigger,
the lock-off lever, and tab.
Speed Control Switch (Fig. A, V)
This brushcutter / string trimmer gives you the choice to
operate at a more efficient speed to extend the runtime
for larger jobs, or accelerate the trimmer speed for high-
performance cutting.
To extend runtime, push the speed control switch
toward the auxiliary handle
mode is best for larger projects that require more time
to complete.
To accelerate the trimmer, pull the speed control switch
back toward the battery housing
This mode is best to cut through heavier growth and for
applications that need higher RPM.
NoTE: When in "HI" mode, runtime will be decreased as
compared to when trimmer is in "LO" mode.
Trimming / Brush cutting (Fig. A, O, P)
With the trimmer on, angle it and swing side to side as
shown in figure O.
Maintain a minimum distance of 610 mm between the guard
and your feet as shown in figure P.
WARNING: Keep the rotating string roughly parallel
with the ground (tilted no more than 30 degrees). This
trimmer is not an edger. DO NOT TILT the trimmer so
that the string or brush cutter blade
a right angle to the ground. Flying debris can cause
serious injury.
Bump Feed Trimmer Line Feed
WARNING: To avoid personal injury, never bump the
unit when the brush cutter assembly is attached to the
motor housing.
Your trimmer uses 2.032 mm diameter nylon line. Cutting
line will wear faster and require more feeding if the cutting
is done along sidewalks or other abrasive surfaces or heavier
weeds are being cut.
As you use the trimmer, the string will get shorter due to
wear. Gently bump the trimmer on the ground while running
at normal speed and the line will feed.
NoTE: Extending nylon line beyond the 380 mm swath will
negatively affect performance, runtime, and the life of the
trimmer due to potential of damaging motor. Doing so may
void the warranty.
Helpful Cutting Tips
•
Use the tip of the string to do the cutting; do not force
string head into uncut grass.
•
Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, curbs, and wood may
wear string rapidly.
34
3
forward,
2
, and then squeeze the variable
5
into the "LO" position. This
6
13
into the "HI" position.
16
is spinning near
•
Do not allow spool cap to drag on ground or other surfaces.
•
In long growth, cut from the top down and do not
exceed 304.8 mm high.
•
Keep trimmer tilted toward the area being cut; this is the
best cutting area.
•
The trimmer cuts when passing the unit from the left to
right. This will avoid throwing debris at the operator.
•
Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by the string.
Replacement Accessories
WARNING: To reduce the risk of serious personal
injury, turn appliance off and remove battery before
forward
making any adjustments or removing/installing
attachments or accessories.
WARNING: The use of any accessory not
recommended by D
could be hazardous.
WARNING: Do not use any blades, or any accessory
or attachment other than those recommended by
D
WALT on this trimmer. Serious injury or product
e
damage may result.
Use D
WALT replacement line Model No. DWO1DT801 (2 mm),
e
DWO1DT802 (2 mm), DWO1DT915 (2.5 mm).
•
For optimal performance, use Dewalt DWO1DT801/802.
D
WALT DWO1DT915 can also be use but may degrade
e
runtime of the trimmer. Using any other line with the
trimmer can degrade performance and/or cause damage to
the trimmer.
Use D
WALT replacement blades Model No. DT20653
e
255 mm (Tri-Blade Brush Knife), DT20654 (255 mm Grass
Cutting Blade), DT20655 (230 mm 4T Grass Cutting Blade).
Replacing the Cutting Line (Fig. A, Q–T)
CAUTION: To avoid appliance damage, if the cutting
line protrudes beyond the trimming blade, cut it off so
that it just reaches the blade.
1. Remove battery pack
2. Turn spool
The white nubs
from the spool window
3. Pull the spool straight out to remove.
4. Remove any dirt and grass from the spool and housing.
5. First, wind new line in the channel of the spool closest to
the holding slots
6. Place the end of the cutting line
hole
41
.
7. Wind the cutting line onto the spool in the direction of
the arrow on the bottom of the spool.
8. When the wound cutting line reaches the beginning of
the holding slots, cut the line approximately 106 mm.
9. Push the line in the holding slots on one side of the spool
to hold the first line while you wind the second line.
10. Repeat the above procedure for the second cutting line
on the lower section of the spool.
WALT for use with this appliance
e
14
.
36
clockwise to unlock as shown in figure Q.
37
inside the spool will rotate away
38
to indicate it is unlocked.
39
as shown in figure R.
40
into the retaining
Publicidad
